TE28F640J3D75

Manufacturer Part NumberTE28F640J3D75
ManufacturerIntel
TE28F640J3D75 datasheet
 


Specifications of TE28F640J3D75

Cell TypeNORDensity64Mb
Access Time (max)75nsInterface TypeParallel
Boot TypeNot RequiredAddress Bus23/22Bit
Operating Supply Voltage (typ)3/3.3VSync/asyncAsynchronous
Package TypeTSOPProgram/erase Volt (typ)2.7 to 3.6V
Operating Temp Range-40C to 85COperating Temperature ClassificationIndustrial
Operating Supply Voltage (min)2.7VOperating Supply Voltage (max)3.6V
Word Size8/16BitNumber Of Words8M/4Mword
MountingSurface MountPin Count56
Lead Free Status / Rohs StatusNot Compliant  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Page 29/68

Download datasheet (911Kb)Embed
PrevNext
Numonyx™ Embedded Flash Memory (J3 v. D)
7.3
Program, Erase, Block-Lock Specifications
Table 12: Configuration Performance
#
Symbol
Write Buffer Byte Program Time
W16
(Time to Program 32 bytes/16 words)
t
WHQV3
W16
Byte Program Time (Using Word/Byte Program Command)
t
EHQV3
Block Program Time (Using Write to Buffer Command)
t
WHQV4
W16
Block Erase Time
t
EHQV4
t
WHQV5
W16
Set Lock-Bit Time
t
EHQV5
t
WHQV6
W16
Clear Block Lock-Bits Time
t
EHQV6
t
WHRH1
W16
Program Suspend Latency Time to Read
t
EHRH1
t
WHRH
W16
Erase Suspend Latency Time to Read
t
EHRH
WY
t
STS Pulse Width Low Time
STS
Notes:
1.
Typical values measured at T
A
set. Subject to change based on device characterization.
2.
These performance numbers are valid for all speed versions.
3.
Sampled but not 100% tested.
4.
Excludes system-level overhead.
5.
These values are valid when the buffer is full, and the start address is aligned on a 32-byte boundary.
6.
Effective per-byte program time (t
7.
Effective per-word program time (t
8.
Max values are measured at worst case temperature, data pattern and V
(except as noted).
9.
Max values are expressed at 25 °C/-40 °C.
7.4
Reset Specifications
Figure 16: AC Waveform for Reset Operation
STS (R)
RP# (P)
Vcc
Note:
STS is shown in its default mode (RY/BY#)
November 2007
308551-05
Parameter
= +25 °C and nominal voltages. Assumes corresponding lock-bits are not
, t
) is 4µs/byte (typical).
WHQV1
EHQV1
, t
) is 8µs/word (typical).
WHQV2
EHQV2
P1
P1
P2
P3
(8)
Typ
Max
Unit
Notes
128
654
µs
1,2,3,4,5,6,7
40
175
µs
1,2,3,4
0.53
2.4
sec
1,2,3,4
1.0
4.0
sec
1,2,3,4
50
60
µs
1,2,3,4,9
0.5
0.70
sec
1,2,3,4,9
15
20
µs
1,2,3,9
15
20
µs
1,2,3,9
500
ns
corner after 100k cycles
CC
Datasheet
1
29