UPC2798GR-E1 CALIFORNIA EASTERN LABS, UPC2798GR-E1 Datasheet
UPC2798GR-E1
Specifications of UPC2798GR-E1
Available stocks
Related parts for UPC2798GR-E1
UPC2798GR-E1 Summary of contents
Page 1
... AGC Input Intercept Point, at MIN Gain 3 DESCRIPTION NEC's UPC2798GR is a Silicon MMIC Downconverter manu- factured with the NESAT™III silicon bipolar process. This product consists of an input AGC amplifier, mixer, local oscil- lator, and video amplifier housed in a small 20 pin SSOP package ...
Page 2
... Notes: -55 to +150 ° CC1 ** @ V CC1 UNITS RATINGS V 6.0 V 11.0 mW 500 -40 to +75 °C -55 to +150 ° MHz -10 dBm, unless otherwise specified) LO UPC2798GR S20 UNITS MIN TYP mA 9.0 12.5 Vp-p 3.0 V/V 200 V 17.0 24.0 Vp-p 3.0 V/V 385 V/V 28 ...
Page 3
... OSC T = 25˚ - AGC Voltage, V AGC (by measurement circuit 1: AGC Amp and Mixer Block) Video Amp 12 10 (V) = 4.0 V AGC = 2.6 V AGC = 0.0 V AGC 150 180 4 5 (V) UPC2798GR CONVERSION GAIN vs. INPUT FREQUENCY 4.0 V AGC 2.6 V AGC 0 - 0.0 V AGC - dBm -10 dBm OSC RF Z, OSC ...
Page 4
STANDARD CHARACTERISTICS DIFFERENTIAL GAIN vs. INPUT FREQUENCY 400 V CC 300 200 100 G1A-G1B : short P = 1.5 V const. OUT p Input Frequency, f (MHz) IN OUTPUT POWER ...
Page 5
STANDARD CHARACTERISTICS GAIN vs. INPUT FREQUENCY CC2 G1A-G1B: short 0 0 Input Frequency, f (MHz) IN GAIN vs. INPUT FREQUENCY ...
Page 6
TYPICAL CHARACTERISTICS CONVERSION GAIN vs. IF FREQUENCY AGC AGC CC1 CC2 G1A - G1B : short 1 KΩ load 25˚C A ...
Page 7
TYPICAL CHARACTERISTICS CONVERSION GAIN vs. INPUT FREQUENCY CC1 CC2 1 KΩ load G1A-G1B : short T = 25˚ 100 150 Input ...
Page 8
STANDARD CHARACTERISTICS THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 0 -20 IM -40 V CC1 V CC2 - MHz MHz 2 f OSC P OSC G1A–G1B: short -80 -50 -40 ...
Page 9
... AGC Voltage, V (V) AGC OSCILLATOR FREQUENCY vs. TUNING VOLTAGE Tuning Voltage, V (V) TU (by application circuit example : MIXER block UPC2798GR NOISE FIGURE vs. AGC VOLTAGE DSB AGC Voltage, V (V) AGC THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER -10 -20 -30 P OUT ...
Page 10
PIN FUNCTIONS Pin Pin Pin Voltage No. Name Typ. (V) 1 AGC IN1 1.5 2 AGC IN2 1 0~5 AGC 5 OSC OUT 4.0 6 GND 0.0 7 OSC B2 2.4 8 OSC ...
Page 11
... Output pins for the downconverter. These are emitter follower outputs which feature low impedance. In the case of a single-ended output, bypass the unused pin to ground through a capacitor. Ground pin. This pin must be connected to system ground. Form ground pattern as wide as possible to minimize ground impedance. UPC2798GR Equivalent Circuit = 1k Ω ...
Page 12
MEASUREMENT CIRCUIT 1 AGC & MIXER BLOCK 10nF AGC IN V AGC 220nF 1nF OSC OUT 10nF 10nF OSC IN MEASUREMENT CIRCUIT 2 VIDEO AMP BLOCK Ω L 10nF 1 2 100k 3 100k ...
Page 13
MEASUREMENT CIRCUIT 3 VIDEO AMP BLOCK Ω L MEASUREMENT CIRCUIT 4 TOTAL BLOCK 10nF AGC IN V AGC 220nF 1nF OSC OUT 10nF 10nF OSC ...
Page 14
... MAX All dimensions are typical unless specified otherwise. ORDERING INFORMATION PART NUMBER UPC2798GR-E1-A Notes: Embossed tape wide. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury ...
Page 15
Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) ...