LMX9838SB National Semiconductor, LMX9838SB Datasheet - Page 28

• Manufacturer Part Number: LMX9838SB
• Manufacturer: National Semiconductor

Specifications of LMX9838SB

• Lead Free Status / Rohs Status: Compliant

www.national.com
20.0 Regulatory Compliance
The LMX9838 has been tested and approved to be compliant
to the following regulatory standards:
CE Compliance:
•
•
IC Compliance:
•
•
FCC Compliance:
•
20.1 FCC INSTRUCTIONS
20.1.1 Safety Information For Rf Exposure
20.1.1.1 FCC Radiation Exposure Statement:
This module may only be installed by the OEM or an OEM
integrator. The antenna used for this transmitter must not be
co-located or operating in conjunction with any other antenna
or transmitter. OEM integrators and End-users and installers
must be provided with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure
compliance.
Only the antenna filed under FCC ID: ED9LMX9838 can be
used with this device.
20.1.1.2 End Product Labeling
FCC ID label on the final system must be labeled with “Con-
tains TX FCC ID: ED9LMX9838 “or “Contains transmitter
module FCC ID: ED9LMX9838”.
IC label on the final system must be labeled with “Contains
TX IC: 1520A-LMX9838” or “Contains transmitter module IC:
1520A-LMX9838”.
20.1.1.3 End Product Manual Information
In the user manual, final system integrator must ensure that
there is no instruction provided in the user manual to install
or remove the transmitter module.
LMX9838SB must be installed and used in strict accordance
with the manufacturer’s instructions as described in the user
documentation that comes with the product.
The following information is required to be incorporated in the
user manual of final system.
USA-Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of FCC
EN 300 328 v1.7.1
EN 301 489-17 v1.2.1
RSS-GEN Issue 1
RSS-210 Issue 7 Annex 8 and RSS-GEN issue 2
FCC Part 15 Subpart C
28
Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with
the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that inter-
ference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by tuning the
equipment off and on, the user is encouraged to try and cor-
rect the interference by one or more of the following mea-
sures:
•
•
•
•
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s au-
thority to operate the equipment.
Caution: Exposure to Radio Frequency Radiation.
This device must not be co-located or operating in conjunction
with any other antenna or transmitter.
Canada – Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including inter-
ference that may cause undesired operation of this device.”
L ‘ utilisation de ce dispositif est autorisée seulement aux
conditions suivantes :
(1) il ne doit pas produire d’interference et
(2) l’ utilisateur du dispositif doit étre pr?t ? accepter toute
interference radioélectrique reçu, m?me si celle-ci est sus-
ceptible de compromettre le fonctionnement du dispositif.
Caution: Exposure to Radio Frequency Radiation.
The installer of this radio equipment must ensure that the an-
tenna is located or pointed such that it does not emit RF field
in excess of Health Canada limits for the general population;
consult Safety Code 6, obtainable from Health Canada’s web-
site www.hc-sc.gc.ca/rpb.
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the
receiver.
Connect the equipment to outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.