G6K2FDC24 Omron, G6K2FDC24 Datasheet
G6K2FDC24
Specifications of G6K2FDC24
Related parts for G6K2FDC24
G6K2FDC24 Summary of contents
Page 1
... Available in 2.54 and 3.2 mm coil-contact terminal spacing. • “-Y” models meet 2.5 kV Bellcore surge requirements. • Conforms to FCC Part 68. • Terminal design based on Omron’s successful G6S relay. • Available in PCB through-hole, SMT gullwing and SMT “inside-L” terminals. ...
Page 2
Coil Data G6K- 2.5 mm coil-contact terminal spacing, standard, non-latching (G6K-2F, G6K-2G, G6K-2P) G6K- 3.2 mm coil-contact terminal spacing, non-latching (G6K-2F-Y, G6K-2G-Y, G6K-2P-Y) Rated voltage Rated current Coil resistance (VDC) (mA) (Ω) 3 33.0 91 4.5 23.2 194 5 ...
Page 3
Characteristic data Maximum Switching Capacity AC resistive load DC resistive load Rated operating voltage (V) Note: The maximum coil voltage refers to the maxi- Electrical Service Life 30 VDC resistive load Ambient temperature: 23°C Switching frequency: 1,800 operations/hour 125 ...
Page 4
Contact Reliability Test (See note.) G6K-2G (F/P), G6K-2G (F/P)-Y NO Sample: G6K-2G contact Number of Relays Test conditions resistive load at contact 10 mVDC with an operation rate Switching frequency: 7,200 operations/h 3 ...
Page 5
Must Operate and Must Release Time Distribution (See note.) G6K-2G (F/P), G6K-2G (F/P)-Y Sample: G6K-2G Must operate Number of Relays: 50 Must release time Time (ms) Note: The tests were conducted at an ambient temperature of 23°C. ■ Approvals UL ...
Page 6
G6K-2F-Y Note: Each value has a tolerance of ±0.3 mm. G6K-2G-Y Note: Each value has a tolerance of ±0.3 mm. G6K-2P-Y Note: Each value has a tolerance of ±0.3 mm. G6KU-2F-Y Note: Each value has a tolerance of ±0.3 mm. ...
Page 7
Packaging Information Tube packing Standard nomenclature Tape packing When ordering, add “TR” before the rated coil voltage (e.g., G6K-2G-TR-DC5). Note not part of the relay model number and will not be marked on the relay. (SMT versions, ...
Page 8
... Time (s) • The thickness of cream solder to be applied should be within a range between 150 and 200 μm on OMRON’s recommended PCB pattern. • In order to perform correct soldering recommended that the correct soldering conditions be maintained as shown below on the left side. Correct Soldering ...
Page 9
Must not cause thermal changes in or deterioration of the insulating material. • Must not cause damage to other control devices. • Must not cause any harmful effect on people. • Must not cause fire. Therefore, be sure to ...
Page 10
MEMO G6K 76 Low Signal Relay ...
Page 11
... Seller within 30 days of receipt of shipment. III. PRECAUTIONS 1. Suitability THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’ ...
Page 12
... THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section. ...