IC SWITCH QUAD SPST 16CDIP

SW06FQ

Manufacturer Part NumberSW06FQ
DescriptionIC SWITCH QUAD SPST 16CDIP
ManufacturerAnalog Devices Inc
SW06FQ datasheet
 


Specifications of SW06FQ

Rohs StatusRoHS non-compliantFunctionSwitch
Circuit4 x SPST - NC/NOOn-state Resistance100 Ohm
Operating Temperature-40°C ~ 85°CMounting TypeThrough Hole
Package / Case16-CDIP (0.300", 7.62mm)  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
Page 1/12

Download datasheet (272Kb)Embed
Next
a
FEATURES
Two Normally Open and Two Normally Closed SPST
Switches with Disable
Switches Can Be Easily Configured as a Dual SPDT or
a DPDT
Highly Resistant to Static Discharge Destruction
Higher Resistance to Radiation than Analog Switches
Designed with MOS Devices
Guaranteed R
Matching: 10% max
ON
Guaranteed Switching Speeds
T
= 500 ns max
ON
T
= 400 ns max
OFF
Guaranteed Break-Before-Make Switching
Low “ON” Resistance: 80
max
Low R
Variation from Analog Input Voltage: 5%
ON
Low Total Harmonic Distortion: 0.01%
Low Leakage Currents at High Temperature
T
= +125 C: 100 nA max
A
T
= +85 C: 30 nA max
A
Digital Inputs TTL/CMOS Compatible and Independent
of V+
Improved Specifications and Pin Compatible to
LF-11333/13333
Dual or Single Power Supply Operation
Available in Die Form
GENERAL DESCRIPTION
The SW06 is a four channel single-pole, single-throw analog
switch that employs both bipolar and ion-implanted FET
devices. The SW06 FET switches use bipolar digital logic inputs
which are more resistant to static electricity than CMOS devices.
Ruggedness and reliability are inherent in the SW06 design and
construction technology.
Increased reliability is complemented by excellent electrical
specifications. Potential error sources are reduced by minimizing
“ON” resistance and controlling leakage currents at high tem-
peratures. The switching FET exhibits minimal R
over a 20 V analog signal range and with power supply voltage
changes. Operation from a single positive power supply voltage
is possible. With V+ = 36 V, V– = 0 V, the analog signal range
will extend from ground to +32 V.
PNP logic inputs are TTL and CMOS compatible to allow the
SW06 to upgrade existing designs. The logic “0” and logic “1”
input currents are at microampere levels reducing loading on
CMOS and TTL logic.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
FUNCTIONAL BLOCK DIAGRAM
1
IN 1
8
IN 2
9
IN 3
16
IN 4
13
DIS
variation
ON
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Quad SPST JFET
Analog Switch
SW06
V+
12
3
S1
2
D1
6
S2
LEVEL
SHIFT
7
D2
11
S3
10
D3
14
S4
15
D4
4
5
GND
V–
Fax: 617/326-8703

SW06FQ Summary of contents

  • Page 1

    FEATURES Two Normally Open and Two Normally Closed SPST Switches with Disable Switches Can Be Easily Configured as a Dual SPDT or a DPDT Highly Resistant to Static Discharge Destruction Higher Resistance to Radiation than Analog Switches Designed with ...

  • Page 2

    SW06–SPECIFICATIONS ELECTRICAL CHARACTERISTICS Parameter Symbol “ON” RESISTANCE R R MATCH BETWEEN SWITCHES R ON ANALOG VOLTAGE RANGE V ANALOG CURRENT RANGE VS. APPLIED VOLTAGE R ON SOURCE CURRENT IN “OFF” CONDITION I S(OFF) DRAIN CURRENT IN “OFF” ...

  • Page 3

    ... Switch is guaranteed by design to provide break-before-make operation. 8 Guaranteed by design. 9 Parameter tested only +125 C for military grade device. A Specifications subject to change without notice. REV +15 V, V– = –15 V, – SW06FQ and – +85 C for SW06GP/GS, unless otherwise noted) A Conditions Min Typ Max Operating – 1.0 mA ...

  • Page 4

    SW06 WAFER TEST LIMITS (@ V+ = +15 V, V– = – Parameter “ON” RESISTANCE R MATCH BETWEEN SWITCHES POSITIVE SUPPLY CURRENT NEGATIVE SUPPLY CURRENT GROUND CURRENT ANALOG VOLTAGE RANGE LOGIC “1” ...

  • Page 5

    ... ABSOLUTE MAXIMUM RATINGS Operating Temperature Range SW06BQ, BRC . . . . . . . . . . . . . . . . . . . – +125 C SW06FQ . . . . . . . . . . . . . . . . . . . . . . . . . – +85 C SW06GP – +85 C Storage Temperature Range . . . . . . . . . . . – +150 C Lead Temperature (Soldering, 60 sec +300 C Maximum Junction Temperature . . . . . . . . . . . . . . . . +150 C V+ Supply to V– Supply . . . . . . . . . . . . . . . . . . . . . . . + Supply to Ground . . . . . . . . . . . . . . . . . . . . . . . . . +36 V Logic Input Voltage . . . . . . . . . . . (– V– Supply Analog Input Voltage Range Continuous . . . . . . . . . . . . . V– ...

  • Page 6

    SW06–Typical Performance Characteristics “ON” Resistance vs. Power Supply Voltage Switch Current vs. Voltage Supply Current vs. Temperature “ON” Resistance vs. Analog Voltage Leakage Current vs. Analog Voltage Supply Current vs. Supply Voltage –6– R vs. Temperature ON Leakage Current vs. ...

  • Page 7

    T /T Switching Response ON OFF Insertion Loss vs. Frequency Power Supply Rejection vs. Frequency REV. A Switching Time vs. Analog Voltage Crosstalk and “OFF” Isolation vs. Frequency Overvoltage Characteristics –7– SW06 Switching Time vs. Temperature Total Harmonic Distortion ...

  • Page 8

    SW06–Typical Performance Characteristics (Operating and Single Supply) “On” Resistance vs. Analog Voltage Switching Time vs. Supply Voltage Leakage Current vs. V ANALOG NOTE These single-supply-operation characteristic curves are valid when the negative power supply V– is tied to the logic ...

  • Page 9

    Isolation Test Circuit REV. A Crosstalk Test Circuit Switching Time Test Circuit –9– SW06 ...

  • Page 10

    SW06 APPLICATIONS INFORMATION The single analog switch product configures, by appropriate pin connections, into four switch applications. As shown in Figure 1, the SW06 connects as a QUAD SPST, a DUAL SPDT, a DUAL DPST DPDT analog switch. ...

  • Page 11

    The switch can easily handle any amount of capacitor discharge current subject only to the maximum heat dissipation of the package and the maximum operating junction temperature from which repetition can be established. SWITCHING Switching time t ...

  • Page 12

    SW06 Single Pole Double Throw Selector Switch with Break-Before-Make Interval 20-Terminal Leadless Chip Carrier (RC-Suffix) E-20A 0.200 (5.08) 0.075 0.100 (2.54) (1.91) 0.064 (1.63) REF 0.095 (2.41) 19 0.075 (1.90) 18 0.358 0.358 (9.09) 0.011 (0.28) (9.09) BOTTOM 0.342 (8.69) ...