2-1376389-3 TE Connectivity, 2-1376389-3 Datasheet
2-1376389-3
Specifications of 2-1376389-3
Available stocks
Related parts for 2-1376389-3
2-1376389-3 Summary of contents
Page 1
... Tel ０４４‐８４４‐８０７９ Fax ０４４‐８１２‐３２０３ ...
Page 2
... A. ...
Page 3
... D. 微小定格 1 mV, 1 µA 以上 E. 適用プリント基板 板厚 1.6 mm 穴径 タイン用穴 : 1.25±0.05 (パンチ加工穴) 1.40± ...
Page 4
... No physical damage Electrical Requirements 3.5.2 Termination Resistance (Low Level Max. (Initial Max. (Final) Subject mated contacts assembled in housing to 20mV Max. open circuit at 10mA. Take the resistance of the wire only away from measurement Fig. 7. EIA 364-23 3.5.3 Insulation Resistance 1000 M Min. (Initial) 500 M Min ...
Page 5
... Test between adjacent circuits and between the surface of housing and contact of mated connectors. EIA 364-20 3.5.5 Temperature Rising 30℃ Max. under loaded specified current. Measure temperature rising by energized current. Subject measurement must do at the place of no influence from convection of air. And contacts assembled in housing all of circuits ...
Page 6
... No electrical discontinuity greater than 1 µsec. shall occur Max. (Final) No electrical discontinuity greater than 1 µsec. shall occur Max. (Final) Subject mated connectors to 10-55-10 Hz traversed in 1 minute at 1.52mm amplitude 2 hours each of 3 mutually perpendicular planes. 100 mA applied. Fig. 8 MIL-STD-202, Method 201A EIA 364-28 3.5.7 ...
Page 7
... Procedures 抜ける 時の荷重を測定すること｡測定は､ AWG #18 もしくは AWG #16 の圧着電線 を使用のこと｡ EIA 364-29 Rev ...
Page 8
... Subject take insulation barrel away. IEC-60512-9-1 3.5.13 Durability (Repeated Mate/Unmating Max. (9.8×Pos.)N Max. Mating (1.0×Pos.)kg Max. Unmat- (1.47×Pos.)N Min. (0.15×Pos.)kg Min. ing No. of Cycles : 25 cycles EIA 364-9 Fig. 3 (続く) (To be Continued) 108-5699 Crimp Tensil (min.) N (kgf) 24 29.4(3) 22 49.0(5) 20 58.8 ( ...
Page 9
... Procedures ストの保持力を測定 操作速度 : 100 mm/分 環 境 的 性 能 Environmental Requirements 項番 No. 試験項目 ...
Page 10
... Environmental Requirements 項番 No. 試験項目 温湿度サイクリング Test Items 規格値 耐電圧 2.2 kVAC 1 分間 (終期) (リーク電流 以下) Requirements 絶 ...
Page 11
... Procedures 環 境 的 性 能 Environmental Requirements Rev.E 5mm Power Key Connector 5mm パワー キイ コネクタ ...
Page 12
... Immersion Duration : 10±0.5 sec. 10±0.5 秒 MIL-STD-202 Condition B EIA 364-56 Incase of manual soldering iron, apply it as 360±10℃ for 3±5℃ seconds without forcing pressure to affect the tine of contact. Fig. 3 (終り) (End) * Product transformation, crack and discoloration. ...
Page 13
... Contact Retention Force 耐熱性 Heat Asing (a) 欄内の数字は試験順序を示す｡ Rev.E 5mm Power Key Connector 5mm パワー キイ コネクタ ...
Page 14
... Contact Retention Force 耐熱性 Heat Asing (a) 欄内の数字は試験順序を示す｡ 5mm Power Key Connector 5mm パワー キイ コネクタ ...
Page 15
... The crimped contacts shall be prepared in accordance with the requirements of applicable application Specification, 114-5292, Crimping of 5mm Pitch W-T-B Connector on the wires specified in Fig this specification. 4.2.2 Applicable Wires : The wires to be used for crimping the samples for ｐerformance testing shall be conforming to the requirements specified in Fig. 6. 素 ...
Page 16
... Fig. 7 Termination Resistance (Low Level) and Temperature Rising Vs. Current Measuring Methods 5mm Power Key Connector 5mm パワー キイ コネクタ Fig. 7 総合抵抗 (ローレベル)､温度上昇 108-5699 Rev. E ...
Page 17
... Fig. 8 Connector Mounting Methods of Low Frequency Vibration and Physical Shock Tests Rev.E 5mm Power Key Connector 5mm パワー キイ コネクタ Fig. 8 低周波振動､物理的衝撃のコネクタ取付方法 108-5699 ...
Page 18
... Fig. 9 Gage Design for Contact Meting/Unmating Force Tests 5mm Power Key Connector 5mm パワー キイ コネクタ Fig. 9 コンタクト挿入引抜力測定用ゲージ 108-5699 Rev. E ...
Page 19
... Descriptions Fig. 11 備 考 Remarks 極 Pos. 極 Pos. 極 Pos. 極 Pos. 極 Pos. 備 考 Remarks 1 列タイプ Single Row Type 2 列タイプ Double Row Type Double Lock Plate □-1376394-□ □-1376395-□ ...