LM4670SD/NOPB National Semiconductor, LM4670SD/NOPB Datasheet

IC AMP AUDIO PWR 3W MONO D 8LLP

LM4670SD/NOPB

Manufacturer Part Number
LM4670SD/NOPB
Description
IC AMP AUDIO PWR 3W MONO D 8LLP
Manufacturer
National Semiconductor
Series
Boomer®r
Type
Class Dr
Datasheet

Specifications of LM4670SD/NOPB

Output Type
1-Channel (Mono)
Max Output Power X Channels @ Load
3W x 1 @ 4 Ohm
Voltage - Supply
2.4 V ~ 5.5 V
Features
Depop, Differential Inputs, Short-Circuit Protection, Shutdown
Mounting Type
Surface Mount
Package / Case
8-LLP
No. Of Channels
1
Output Power
3W
Supply Voltage Range
2.4V To 5.5V
Load Impedance
100kohm
Operating Temperature Range
-40°C To +85°C
Amplifier Case Style
LLP
No. Of Pins
8
Msl
MSL 1 - Unlimited
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
LM4670SD

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM4670SD/NOPB
Manufacturer:
TI/NS
Quantity:
2 500
© 2006 National Semiconductor Corporation
LM4670
Filterless High Efficiency 3W Switching Audio Amplifier
General Description
The LM4670 is a fully integrated single-supply high efficiency
switching audio amplifier. It features an innovative modulator
that eliminates the LC output filter used with typical switching
amplifiers. Eliminating the output filter reduces external com-
ponent count, simplifies circuit design, and reduces board
area. The LM4670 processes analog inputs with a delta-
sigma modulation technique that lowers output noise and
THD when compared to conventional pulse width modula-
tors.
The LM4670 is designed to meet the demands of mobile
phones and other portable communication devices. Operat-
ing on a single 5V supply, it is capable of driving a 4Ω
speaker load at a continuous average output of 2.3W with
less than 1% THD+N. Its flexible power supply requirements
allow operation from 2.4V to 5.5V.
The LM4670 has high efficiency with speaker loads com-
pared to a typical Class AB amplifier. With a 3.6V supply
driving an 8Ω speaker, the IC’s efficiency for a 100mW
power level is 77%, reaching 88% at 600mW output power.
The LM4670 features a low-power consumption shutdown
mode. Shutdown may be enabled by driving the Shutdown
pin to a logic low (GND).
The gain of the LM4670 is externally configurable which
allows independent gain control from multiple sources by
summing the signals.
Typical Application
Boomer
®
is a registered trademark of National Semiconductor Corporation.
FIGURE 1. Typical Audio Amplifier Application Circuit
DS200899
Key Specifications
Features
n No output filter required for inductive loads
n Externally configurable gain
n Very fast turn on time: 1.35ms (typ)
n Minimum external components
n "Click and pop" suppression circuitry
n Micro-power shutdown mode
n Short circuit protection
n Available in space-saving microSMD and LLP packages
Applications
n Mobile phones
n PDAs
n Portable electronic devices
j
j
j
j
j
j
Efficiency at 3.6V, 100mW into 8Ω speaker 77% (typ)
Efficiency at 3.6V, 600mW into 8Ω speaker 88% (typ)
Efficiency at 5V, 1W into 8Ω speaker
Quiescent current, 3.6V supply
Total shutdown power supply current
Single supply range
20089901
www.national.com
2.4V to 5.5V
0.01µA (typ)
4.8mA (typ)
87% (typ)
July 2006

Related parts for LM4670SD/NOPB

LM4670SD/NOPB Summary of contents

Page 1

... Typical Application FIGURE 1. Typical Audio Amplifier Application Circuit Boomer ® registered trademark of National Semiconductor Corporation. © 2006 National Semiconductor Corporation Key Specifications j Efficiency at 3.6V, 100mW into 8Ω speaker 77% (typ) j Efficiency at 3.6V, 600mW into 8Ω speaker 88% (typ) j Efficiency at 5V, 1W into 8Ω ...

Page 2

Connection Diagrams 9 Bump micro SMD Package Top View Order Number LM4670ITL, LM4670ITLX See NS Package Number TLA09ZZA Leadless Leadframe Package (LLP) Top View Order Number LM4670SD See NS Package Number SDA08A Contact NSC Sales Office for Availability www.national.com micro ...

Page 3

... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (Note 1) Storage Temperature + 0.3V ≥ V ≥ GND - 0.3V Voltage at Any Input Pin V DD Power Dissipation (Note 3) ESD Susceptibility (Note 4) ...

Page 4

Electrical Characteristics The following specifications apply for A apply for T = 25˚C. (Continued) A Symbol Parameter P Output Power (Note 11) O THD+N Total Harmonic Distortion + Noise PSRR Power Supply Rejection Ratio SNR Signal to Noise Ratio e ...

Page 5

Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, ...

Page 6

Typical Performance Characteristics THD+N vs Frequency V = 2.5V 15µH + 4Ω + 15µ 375mW, 22kHz BW OUT THD+N vs Frequency 15µH + 4Ω + 15µ ...

Page 7

Typical Performance Characteristics THD+N vs Output Power R = 15µH + 4Ω + 15µ 1kHz, 22kHz BW CMRR vs Frequency V = 3.6V 15µH + 8Ω + 15µ Sine Wave, ...

Page 8

Typical Performance Characteristics Output Power vs Supply Voltage R = 15µH + 4Ω + 15µ 1kHz, 22kHz BW L Supply Current (RMS) vs Output Power R = 15µH + 4Ω + 15µ 1kHz L Shutdwon Threshold ...

Page 9

Typical Performance Characteristics Supply Current vs Shutdown Voltage R = 15µH + 8Ω + 15µH L Supply Current vs Supply Voltage R = Different µH loads L (Note 10) (Continued) Supply Current vs Supply Voltage R L 20089938 Differential Gain ...

Page 10

Application Information GENERAL AMPLIFIER FUNCTION The output signals generated by the LM4670 consist of two, BTL connected, output signals that pulse momentarily from near ground potential The two outputs can pulse DD independently with the exception that ...

Page 11

Application Information current usage while in the shutdown state. While the LM4670 may be disabled with shutdown voltages in between ground and supply, the idle current will be greater than the typical 0.01µA value. Increased THD may also be observed ...

Page 12

Application Information FIGURE 3. Differential input configuration with input capacitors www.national.com (Continued) FIGURE 2. Differential input configuration 12 20089903 20089904 ...

Page 13

Application Information FIGURE 4. Dual differential input configuration (Continued) FIGURE 5. Single-ended input configuration 13 20089905 20089906 www.national.com ...

Page 14

Application Information FIGURE 7. Dual input with a single-ended input and a differential input www.national.com (Continued) FIGURE 6. Dual single-ended input configuration 14 20089907 20089908 ...

Page 15

Application Information REFERENCE DESIGN BOARD SCHEMATIC In addition to the minimal parts required for the application circuit, a measurement filter is provided on the evaluation circuit board so that conventional audio measurements can be conveniently made without additional equipment. This ...

Page 16

Application Information LM4670 micro SMD BOARD ARTWORK Composite View Top Layer Internal Layer 2, V www.national.com (Continued) 20089932 20089937 DD 20089934 16 Silk Screen 20089935 Internal Layer 1, GND 20089933 Bottom Layer 20089931 ...

Page 17

Application Information LM4670 SDA BOARD ARTWORK Composite View Top Layer Internal Layer 2, V (Continued) 20089953 20089957 DD 20089955 17 Silk Screen 20089956 Internal Layer 1, GND 20089954 Bottom Layer 20089952 www.national.com ...

Page 18

Revision History Rev Date 1.0 12/15/04 1.1 7/06/05 1.2 7/13/06 www.national.com Description Initial WEB of the D/S (TL pkg). Re-released D/S to the WEB (added the SD package). Edited Note 9, then re-released D/S to the WEB. 18 ...

Page 19

Physical Dimensions inches (millimeters) unless otherwise noted 9 Bump micro SMD Order Number LM4670ITL, LM4670ITLX NS Package Number TLA09ZZA X1 = 1.463 X2 = 1.463 X3 = 0.600 LLP Order Number LM4670SD NS Package Number SDA08A 19 www.national.com ...

Page 20

... BANNED SUBSTANCE COMPLIANCE National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at: www.national.com/quality/green. ...

Related keywords