AAT3216IGV-2.5-T1 Advanced Analogic Technologies, Inc., AAT3216IGV-2.5-T1 Datasheet
AAT3216IGV-2.5-T1
Available stocks
Related parts for AAT3216IGV-2.5-T1
AAT3216IGV-2.5-T1 Summary of contents
Page 1
General Description The AAT3216 MicroPower low dropout (LDO) lin- ear regulator is ideally suited for portable applica- tions where low noise, extended battery life, and small size are critical. The AAT3216 has been specifically designed for low output noise perform- ...
Page 2
Pin Descriptions Pin # Symbol SOT23-5 SC70JW GND POK OUT Pin Configuration SOT23-5 (Top View GND 150mA MicroPower™ LDO ...
Page 3
Absolute Maximum Ratings T = 25°C, unless otherwise noted. A Symbol Description V POK Input Voltage, POK IN, V Maximum EN to Input Voltage ENIN(MAX Output Current OUT T Operating Junction Temperature Range J Thermal Information 2 Symbol ...
Page 4
Electrical Characteristics for V options greater than 1.5V OUT(NOM) OUT C = 1µ -40°C to +85°C, unless otherwise noted. Typical values are Symbol Description V Output Voltage ...
Page 5
Typical Characteristics Unless otherwise noted 5V Dropout Voltage vs. Temperature 260 240 220 I = 150mA L 200 180 160 I = 100mA 140 L 120 100 50mA ...
Page 6
Typical Characteristics Unless otherwise noted 5V Turn-On Time and POK Delay V ENABLE V OUT V POK Time (10µs/div) Line Transient Response OUT Time ...
Page 7
Typical Characteristics Unless otherwise noted 5V AAT3216 Self Noise 10 1 0.1 0.01 0.01 0 Frequency (kHz) 3216.2006.01.1.3 150mA MicroPower™ LDO with PowerOK = 25°C. A 1.250 1.225 1.200 1.175 1.150 1.125 1.100 1.075 ...
Page 8
Functional Block Diagram IN EN POK Functional Description The AAT3216 is intended for LDO regulator appli- cations where output current load requirements range from no load to 150mA. The advanced circuit design of the AAT3216 pro- vides excellent transient response ...
Page 9
Applications Information To assure the maximum possible performance is obtained from the AAT3216, please refer to the fol- lowing application recommendations. Input Capacitor Typically, a 1µF or larger capacitor is recommend- ed for C in most applications ...
Page 10
POK Output The AAT3216 features an integrated Power-OK comparator which can be used as an error flag. The POK open-drain output goes low when OUT is 6% below its nominal regulation voltage. Connect a pull-up resistor from POK to OUT ...
Page 11
The following discussions will assume the LDO reg- ulator is mounted on a printed circuit board utilizing the minimum recommended footprint as stated in the Layout Considerations section of this document. At any given ambient temperature (T mum package power ...
Page 12
LDO regulator in a duty-cycled mode. For example, an application requires V while 150mA load and T OUT V is greater than 3.90V, which is the maximum IN safe ...
Page 13
... For example, a 2.5V system using a AAT3216IGV- 2.5-T1 operates at a continuous 100mA load cur- rent level and has short 150mA current peaks. The current peak occurs for 378µs out of a 4.61ms peri- od ...
Page 14
... Sample stock is generally held on part numbers listed in BOLD. 14 150mA MicroPower™ LDO with PowerOK Marking 1 Part Number (Tape and Reel) EAXYY AAT3216IGV-1.2-T1 KJXYY AAT3216IGV-1.5-T1 AAT3216IGV-1.8-T1 AAT3216IGV-2.0-T1 AAT3216IGV-2.3-T1 KKXYY AAT3216IGV-2.5-T1 AAT3216IGV-2.7-T1 ELXYY AAT3216IGV-2.8-T1 AAT3216IGV-2.85-T1 AAT3216IGV-3.0-T1 HQXYY AAT3216IGV-3.3-T1 IYXYY AAT3216IGV-3.5-T1 AAT3216IJS-1.2-T1 AAT3216IJS-1.5-T1 AAT3216IJS-1.8-T1 AAT3216IJS-2.0-T1 AAT3216IJS-2 ...
Page 15
Package Information 2.85 ± 0.15 1.90 BSC 0.95 BSC 0.60 REF 10° ± 5° 0.40 ± 0.10 0.50 BSC 0.50 BSC 0.50 BSC 2.00 ± 0.20 7° ± 3° All dimensions in millimeters 3216.2006.01.1.3 150mA MicroPower™ LDO with PowerOK SOT23-5 ...
Page 16
... Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. ...