ILX532A Sony, ILX532A Datasheet

no-image

ILX532A

Manufacturer Part Number
ILX532A
Description
7500-pixel CCD Linear Sensor(B/W)
Manufacturer
Sony
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ILX532A
Manufacturer:
SONY
Quantity:
6 243
Part Number:
ILX532A
Manufacturer:
SONY/索尼
Quantity:
20 000
Description
developed for high resolution copiers. This sensor
reads A3-size documents at a density of 600DPI, at
high speed.
Features
• Number of effective pixels: 7500 pixels
• Pixel size:
• Clamp circuit are on-chip
• Signal output phase of two-output
• Ultra high sensitivity/Ultra low lag
• Max Data Rate:
• Single 12V power supply
• Input Clock Pulse:
• Package:
Absolute Maximum Ratings
• Supply voltage
• Operating temperature
• Storage temperature
Pin Configuration (Top View)
The ILX532A is a reduction type CCD linear sensor
simultaneous-output (alternate-output is available)
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
7500-pixel CCD Linear Sensor (B/W)
V
CLP-
OUT
RS-
LH-
2-
1-
GND
ROG
-
V
V
ODD
ODD
ODD
ODD
ODD
ODD
NC
NC
NC
NC
GG
DD
10
11
12
13
14
1
2
3
4
5
6
7
8
9
7500
1
V
DD
7µm
40MHz
CMOS 5V drive
28 pin Cer-DIP (400mil)
–10 to +60
–30 to +80
28
27
26
25
24
23
22
21
20
19
18
17
16
15
15
7µm (7µm pitch)
V
V
V
NC
NC
GND
V
GND
NC
CLP-
RS-
LH-
2-
1-
DD
OUT
DD
DD
EVEN
EVEN
EVEN
EVEN
-
EVEN
EVEN
°C
°C
V
– 1 –
Block Diagram
28 pin DIP (Cer-DIP)
ILX532A
S7500
S7499
D94
D75
D74
D26
D25
S2
S1
E98344-PS

Related parts for ILX532A

ILX532A Summary of contents

Page 1

... CCD Linear Sensor (B/W) Description The ILX532A is a reduction type CCD linear sensor developed for high resolution copiers. This sensor reads A3-size documents at a density of 600DPI, at high speed. Features • Number of effective pixels: 7500 pixels • Pixel size: 7µm • Clamp circuit are on-chip • ...

Page 2

... EVEN Min. Typ. — 500 — — — 10 CLP — 10 ROG , LH- as LH, RS- ODD EVEN Min. Typ. — 1 — 2 Min. Typ. — 0 4.75 5.0 ILX532A Max. Unit — pF — pF — pF — pF — ODD Max. Unit 20 MHz 40 MHz Max. Unit 0.1 V 5.25 V ...

Page 3

... V 0.23 — lx · 0.3 2.0 mV 0.6 5.0 mV 0.02 — — % Ω 150 — 6.5 — the minimum output to V and the average MIN . EVEN-AVE ILX532A Remarks Note 2 Note 3 Note 4 Note 5 Note 6 Note 7 Note 8 Note 9 Note 10 — — — Note 11 ...

Page 4

... D93 D94 D83 D84 D81 D82 D79 D80 D77 D78 D75 D76 S7499 S7500 S7497 S7498 S7495 S7496 D73 D74 D71 D72 D69 D70 D27 D28 D25 D26 D23 D24 ILX532A ...

Page 5

... Clock Timing Chart 2 ROG Clock Timing Chart t13 CLP V OUT Clock timing LH, RS, CLP and V alternate output t16 at odd or even are the same as timing chart 3 in the case of OUT – 5 – t10 t11 t8 t14 t15 t12 t17 ILX532A ...

Page 6

... Clock Timing Chart 4 Cross point 1 and Cross point LH and 1.5V (Min.) 2.0V (Min.) – 6 – ILX532A 1.5V (Min.) 1.5V (Min.) ...

Page 7

... D94 D93 D84 D83 D82 D81 D80 D79 D78 D77 D76 D75 S7500 S7499 S7498 S7497 S7496 S7495 D74 D73 D72 D71 D70 D69 D28 D27 D26 D25 D24 D23 – 7 – ILX532A ...

Page 8

... Signal output delay time 1 These timing is the recommended condition under 1MHz. Symbol Min 1000 t3 1000 t10 0 t11 0 t12 10 t13 5 t14 0 t15 0 t16 — t17 — – 8 – ILX532A Typ. Max. Unit 100 — ns 1500 — ns 1500 — 200 — 200 — 200 — ...

Page 9

... NC NC GND NC V ROG EVEN DD GND 1- ODD EVEN 2- ODD 0 EVEN OUT ODD OUT DD V GND LH- LH- EVEN ODD 100 RS- RS- EVEN ODD 100 CLP- CLP- EVEN ODD – 9 – ILX532A ...

Page 10

... V [ 12V 25°C) DD 500 600 700 800 Wavelength [nm] Integration time output voltage characteristics 1 0.5 0 Vos 0 12.6 – 10 – 900 1000 (Standard characteristics int – integration time [ms] Offset level vs. Temperature characteristics (Standard characteristics) Vos – Ambient temperature [ C] ILX532A 10 –2mV ...

Page 11

... For repairs and remount, cool sufficiently dismount an imaging device, do not use a solder suction equipment. When using an electric desoldering tool, ground the controller. For the control system, use a zero cross type. 29N 29N (2) (3) – 11 – ILX532A 0.9Nm (4) ...

Page 12

... Keep in a case to protect from dust and dirt. To prevent dew condensation, preheat or precool when moving to a room with great temperature differences. 5) Exposure to high temperatures or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. 6) CCD image sensors are precise optical equipment that should not be subject to mechanical shocks. – 12 – ILX532A ...

Page 13

... ILX532A ...

Related keywords