ICX284AK Sony, ICX284AK Datasheet
ICX284AK
Available stocks
Related parts for ICX284AK
ICX284AK Summary of contents
Page 1
... Diagonal 6.64mm (Type 1/2.7) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras Description The ICX284AK is a diagonal 6.64mm (Type 1/2.7) interline CCD solid-state image sensor with a square pixel array and 2.02M effective pixels. Frame readout allows all pixels' signals to be output independently within approximately 1/7 ...
Page 2
... Horizontal register Description Pin No – 2 – Note) Note) : Photo sensor 15 16 Symbol Description V Supply voltage DD GND GND SUB Substrate clock 1 C Substrate bias SUB V Protective transistor bias L RG Reset gate clock H Horizontal register transfer clock 1 H Horizontal register transfer clock 2 ICX284AK ...
Page 3
... SUB , – GND – GND – GND – – – 3 – ICX284AK Unit Remarks Ratings –40 to +12 V –50 to +15 V –50 to +0.3 V –40 to +0.3 V – –0.3 to +22 V –10 to +18 V –10 to +6.5 V –0.3 to +28 V –0 +15 V –6.5 to +6.5 V –10 to +16 V –30 to +80 °C – ...
Page 4
... Max. Unit Remarks 15.45 V Max. Unit Remarks mA Waveform Unit Remarks diagram VH1 VL3 – High-level coupling V 2 High-level coupling V 2 Low-level coupling V 2 Low-level coupling Cross-point voltage Low-level coupling V 4 Low-level coupling ICX284AK power L )/2 VH2 )/2 VL4 ...
Page 5
... V1B3A C V24 V1A1B V3A3B SUB GND V23B C V V23A V3A C V3A3B C V1A3B C V3B V3A4 V 3B V3B4 Horizontal transfer clock equivalent circuit – 5 – Min. Typ. Max. Unit pF 390 pF 1200 pF 1500 pF 120 pF 470 120 620 Ω 56 Ω 62 Ω 91 Ω 18 Ω ICX284AK Remarks ...
Page 6
... VLH V VLL VHH VHH V V VHL V VH2 V VL2 V VLL )/2 VH VH1 VH2 )/2 VL VL3 VL4 – twh VHH V VHL V VHL V VL3 VHL V VLH V VLL V VL4 – 6 – VHH VHH V VHL V VH3 V VLL VHH VHH VHL VHL V VH4 V VLH V VL ICX284AK V VLH ...
Page 7
... CCD) twh two 1 twh tf V RGH V RG Point A is the minimum value of the coupling waveform during the period from RGLL and V . RGLH RGLL . RGLm 100% 90% V SUB 10 twh – 7 – twl V and H waveforms and H is two. 2 twl ICX284AK RGL ...
Page 8
... Gr Mg 450 500 550 Wave Length [nm] – 8 – Unit Remarks 0.5 0.5 µs 15 250 ns 8 8.5 14 8.5 14 0.01 0.01 µs 0.01 0. 0.5 0.5 µs Remarks 600 650 700 ICX284AK During readout When using CXD1267AN tf ≥ tr – 2ns During drain charge ...
Page 9
... Ignored region Effective pixel region AMP S/H S/H – 9 – Measurement Remarks method 1 1/30s accumulation 60°C Frame readout mode, 4 High frame rate readout mode Zone 0 and 5 Zone 60°C, 7.5frame 60°C, 7.5frame/s, 8 G/Ye channel signal output [ B] Mg/Cy channel signal output [ C] ICX284AK (Ta = 25° ...
Page 10
... The complementary color filters of this image sensor are arranged in the layout shown in the figure on the left. A2 For frame readout, the A1 and A2 lines are output as signals in the A field, and the B1 and B2 lines in the B field. A1 Horizontal register 1/4 – 10 – ICX284AK ...
Page 11
... All effective area signals are output in 1/4 the period for frame readout mode by reading out two lines for every eight lines. The number of output lines is 325 lines. This readout mode emphasizes processing speed over vertical resolution. 2nd field OUT – 11 – ICX284AK High frame rate readout mode OUT ...
Page 12
... Ysm log 150 500 2 , color temperature of 3200K halogen source subject. (Pattern , and the center of each G, Mg, Ye and Cy channel [mV]) and Cy signal output ( [dB] (1/10V method conversion value) 10 – 12 – ICX284AK [mV]) and G Mg [mV]) at the center of Cy ...
Page 13
... Adjust the G/Mg/Ye/Cy channel signal output generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) 100 [%] VD Strobe light timing Output Light G/Mg/Ye/Cy channel signal output 150mV Vlag (lag) – 13 – ICX284AK ...
Page 14
... ICX284AK ...
Page 15
... ICX284AK ...
Page 16
... ICX284AK ...
Page 17
... ICX284AK ...
Page 18
... ICX284AK ...
Page 19
... ICX284AK ...
Page 20
... ICX284AK ...
Page 21
... ICX284AK ...
Page 22
... ICX284AK ...
Page 23
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 50N 50N Compressive strength – 23 – ICX284AK 1.2Nm Torsional strength ...
Page 24
... For continuous using under cruel condition exceeding the normal using condition, consult our company. b) Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) Brown stains may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. – 24 – ICX284AK ...
Page 25
... ICX284AK ...