ILX514 Sony, ILX514 Datasheet
ILX514
Related parts for ILX514
ILX514 Summary of contents
Page 1
... CCD Linear Image Sensor (B/W) For the availability of this product, please contact the sales office. Description The ILX514 is a reduction type CCD linear sensor developed for high resolution facsimiles and copiers. This sensor reads A4-size documents at a density of 400 DPI (Dot Per Inch). A built-in timing generator and clock-drivers ensure direct drive at 5V logic for easy use ...
Page 2
... ILX514 ...
Page 3
... RS/SH Clock pulse or with S/H; without S/H switch power supply DD1 22 CLK Clock pulse 1 Output mode is changeable as follows. 20pin GND 9pin Internal RS GND without S/H — V DD1 Description V RS DD1 Internal RS — with S/H External RS — without S/H – 3 – ILX514 ...
Page 4
... Input capacity of RS/SH pin Frequency of CLK Frequency of RS Max. Unit 9.5 V 5.25 V (9V) and then V DD1 (5V) and then V (9V). DD2 DD1 Symbol Min. Typ. C — 10 CLK C — 10 ROG C — 10 RS/SH f — 1 CLK f — – 4 – (5V). DD2 Max. Unit — pF — pF — MHz 5 MHz ILX514 ...
Page 5
... V 5000 — — , the minimum output to V MAX MIN ILX514 Remarks Note 2 Note 3 Note 4 Note 5 Note 6 Note 7 Note 8 Note 9 Note 10 — — — — Note 11 Note 12 and the ...
Page 6
... Optical signal accumulated time int stands at 10ms. 10 500mV (Typ.) OUT 11) Vos is defined as indicated below. Vout V OS GND 12) Dynamic range is defined as follows. V SAT DRK When optical accumulated time is shorter, the dynamic range gets wider because dark voltage is in proportion to optical accumulated time. – 6 – ILX514 ...
Page 7
... ILX514 ...
Page 8
... ILX514 ...
Page 9
... Clock Pulse Waveform Conditions CLK, ROG pulse related Internal RS mode CLK Vout External RS mode CLK ROG t1 t3 CLK t10 t11 t13 t12 – 9 – t10 t10 ILX514 ...
Page 10
... Signal output delay time 1 Recommended condition during CLK = 1MHz. Symbol t8 High level CLK ROG V Low level RS t10 Internal RS t11 t12 External RS t13 – 10 – ILX514 Min. Typ. Max. Unit 100 200 — ns 800 1000 — ns 800 1000 — 100 500 — 100 500 — ns ...
Page 11
... Wavelength [nm] Spatial frequency [cycles/mm] 0 14.3 28.6 42.9 1.0 0.8 0.6 0.4 0 0.2 0.4 0.6 Normalized spatial frequency Integration time output voltage characteristics 1 0.5 0 – 11 – 800 900 1000 57.1 71.4 0.8 1.0 (Standard characteristics int – Integration time [ms] ILX514 10 ...
Page 12
... Operational frequency characteristics of the V DD1 supply current (Standard characteristics CLK – CLK clock frequency [MHz] Offset level vs 0. 9.5 (Standard characteristics) Vos –0.8mV/° – Ambient temperature [°C] – 12 – DD2 characteristics DD2 (Standard characteristics 25°C Vos –0.14 V DD2 4.75 5 5.25 V [V] DD2 60 ILX514 ...
Page 13
... Prying the upper or lower ceramic layers away at a support point of the low-melting glass. Note that the preceding notes should also be observed when removing a component from a board after it has already been soldered. (9V) and then V DD1 (9V). DD1 of the glass portion.) 29N/surface 29N/surface 0.9Nm 29N (2) – 13 – (5V). DD2 29N (3) ILX514 0.9Nm (4) ...
Page 14
... Keep in a case to protect from dust and dirt. To prevent dew condensation, preheat or precool when moving to a room with great temperature differences. 6) Exposure to high temperatures or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. 7) CCD image sensors are precise optical equipment that should not be subject to mechanical shocks. – 14 – ILX514 ...
Page 15
... ILX514 ...