MC12009P Motorola, MC12009P Datasheet
MC12009P
Available stocks
Related parts for MC12009P
MC12009P Summary of contents
Page 1
... MC12013 Rating Unit MTTL Output –8.0 Vdc Vdc mAdc 100 –65 to +175 C –30 to +85 C Device 70 — MC12009P MC12011P MC12013P Motorola, Inc. 1997 Order this document by MC12009/D MC12009 MC12011 MC12013 SEMICONDUCTOR TECHNICAL DATA SUFFIX PLASTIC PACKAGE CASE 648 PIN CONNECTIONS CCO 1 16 ...
Page 2
... MTTL – Out Q4 MECL Toggle to Flip MTTL Flop Trans– lator MTTL – Out Q4 MECL Toggle to Flip MTTL Flop Trans– lator MTTL – Out Voltage–Controlled f out Oscillator MC1648 MC12009 MC12011 MC12013 B A Programmable Counter MC4016 MOTOROLA RF/IF DEVICE DATA ...
Page 3
... The circuit test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50 resistor to –2.0 V. Test procedures are shown for only one gate. The other gates are tested in the same manner. MOTOROLA RF/IF DEVICE DATA MC12009 MC12011 MC12013 Pi Pin – ...
Page 4
... Gnd ILAmax 1,16 6 1,16 1,16 1,16 1, 1,16 10 1,16 1,16 1,16 1,16 1,16 9 1,16 10 1,16 1,16 9,10 1,16 9,10 1,16 6 9,10 1,16 9,10 1,16 6 1,16 1,16 11,12,13 1,16 11,12,13 1, Clock Input V IHmax V ILmin MOTOROLA RF/IF DEVICE DATA ...
Page 5
... In addition to meeting the output levels specified, the device must divide during this test. The clock input is the waveform shown addition to meeting the output levels specified, the device must divide during this test. The clock input is the waveform shown. MOTOROLA RF/IF DEVICE DATA MC12009 MC12011 MC12013 TEST VOLTAGE/CURRENT VALUES Volts ...
Page 6
... Vdc 4.000 4.190 4.070 4.300 2.6 2.8 3.110 3.410 3.135 3.445 Vdc 3.110 3.410 3.135 3.445 0.80 0.72 3.980 4.050 Vdc 3.980 4.050 3.430 3.465 Vdc 3.430 3.465 –65 –20 –65 –20 mAdc Clock Input V IHmax V ILmin MOTOROLA RF/IF DEVICE DATA ...
Page 7
... In addition to meeting the output levels specified, the device must divide during this test. The clock input is the waveform shown addition to meeting the output levels specified, the device must divide during this test. The clock input is the waveform shown. MOTOROLA RF/IF DEVICE DATA MC12009 MC12011 MC12013 TEST VOLTAGE/CURRENT VALUES V IHmax ...
Page 8
... –0.25 16 –0.40 –0.25 16 –0.40 –0.25 16 –0. Gnd 8,15 8,11 8,12 8, Clock Input V IHmax V ILmin MOTOROLA RF/IF DEVICE DATA ...
Page 9
... Pulse 10% Generator +1 (Pin 2) Divide by 5 — MC12009 Divide by 8 — MC12011 Divide by 10 — MC12013 MOTOROLA RF/IF DEVICE DATA MC12009 MC12011 MC12013 MC12009, MC12011, MC12013 TEST VOLTAGES/WAVEFORMS APPLIED TO PINS LISTED BELOW: +25 C +85 C Pulse Pulse Pulse Pulse Min Typ Max ...
Page 10
... The 1950–ohm resistor at Pin 7 and the scope termination impedance constitute attenuator probe total parasitic capacitance which includes probe, wiring, and load capacitance. Unused output connected to a 50–ohm resistor to ground. V out (Scope Channel B) V out 0 out 1950 –3.0 V MOTOROLA RF/IF DEVICE DATA ...
Page 11
... Figure 6. Maximum Frequency Test Circuit (To Scope) Sine Wave Input 800 mV Clock Input 3 Cycles Q (Pin 2) 800 mV Clock Input Q (Pin 2) 800 mV Clock Input Q (Pin 2) MOTOROLA RF/IF DEVICE DATA MC12009 MC12011 MC12013 +2 –3.0 V Unused output connected DIVIDE BY 6 850 mV typ 3 Cycles ...
Page 12
... Enable = 1 1101 1011 DIVIDE BY 10/11 (MC12013) 1101 1001 Enable = 1 0001 0100 0011 0111 001 010 101 000 1000 1100 1010 0000 0111 1111 0001 1001 0011 0100 1110 0110 0101 0010 0000 1011 1010 1000 1100 1111 MOTOROLA RF/IF DEVICE DATA ...
Page 13
... MTTL 4 7 Trans– – lator MOTOROLA RF/IF DEVICE DATA MC12009 MC12011 MC12013 APPLICATIONS INFORMATION of the five gate inputs E1 through E5 are high. Division occurs when all inputs E1 through E5 are low. (Unconnected MTTL inputs are normally high, uncon- nected MECL inputs are normally low). With the addition of extra parts, many different division configurations may be obtained (20/21, 40/41, 50/51, 100/101, etc ...
Page 14
... Pins 2 and 3 respectively, and driving the MTTL flip–flop with Pin 7. MC12013 inputs E4 and E5 are used rather than E1. With operation remains as shown. Figure 10. Divide By 40/41 (MC12013 MC10131 For For Termination resistors for MECL outputs are not shown, but are required except for the flip–flop driving the translator section. MOTOROLA RF/IF DEVICE DATA ...
Page 15
... Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “ ...