X24C08P Xicor, X24C08P Datasheet
X24C08P
Available stocks
Related parts for X24C08P
X24C08P Summary of contents
Page 1
... The X24C08 features a serial interface and software protocol allowing operation on a simple two wire bus. The X24C08 is fabricated with Xicor’s advanced CMOS Textured Poly Floating Gate Technology. The X24C08 utilizes Xicor’s proprietary Direct Write™ ...
Page 2
X24C08 PIN DESCRIPTIONS Serial Clock (SCL) The SCL input is used to clock all data into and out of the device. Serial Data (SDA) SDA is a bidirectional pin used to transfer data into and out of the device. It ...
Page 3
X24C08 DEVICE OPERATION The X24C08 supports a bidirectional bus oriented pro- tocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is a ...
Page 4
X24C08 Acknowledge Acknowledge is a software convention used to indicate successful data transfers. The transmitting device will release the bus after transmitting eight bits. During the ninth clock cycle the receiver will pull the SDA line LOW to acknowledge that ...
Page 5
X24C08 DEVICE ADDRESSING Following a start condition the master must output the address of the slave it is accessing. The most significant four bits of the slave address are the device type identifier (see Figure 4). For the X24C08 this ...
Page 6
X24C08 Page Write The X24C08 is capable of a sixteen byte page write operation initiated in the same manner as the byte write operation, but instead of terminating the write cycle after the first data word is transferred, ...
Page 7
X24C08 READ OPERATIONS Read operations are initiated in the same manner as write operations with the exception that the R/W bit of the slave address is set to a one. There are three basic read operations: current address read, random ...
Page 8
X24C08 Sequential Read Sequential reads can be initiated as either a current address read or random access read. The first word is transmitted as with the other read modes; however, the master now responds with an acknowledge, indicating it requires ...
Page 9
X24C08 ABSOLUTE MAXIMUM RATINGS* Temperature Under Bias ................. – +135 C Storage Temperature ...................... – +150 C Voltage on any Pin with Respect to V ................................. –1.0V to +7V SS D.C. Output Current ........................................... 5 mA ...
Page 10
X24C08 A.C. CONDITIONS OF TEST Input Pulse Levels Input Rise and Fall Times I/O Timing Levels A.C. CHARACTERISTICS LIMITS (Over recommended operating conditions, unless otherwise specified.) Read & Write Cycle Limits Symbol t SCL ...
Page 11
X24C08 WRITE CYCLE LIMITS Symbol Parameter (6) t Write Cycle Time WR The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle. During the write cycle, ...
Page 12
X24C08 NOTES 12 ...
Page 13
X24C08 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESIS IN MILLIMETERS) 0.150 (3.80) 0.158 (4.00) PIN 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7 ...
Page 14
X24C08 PACKAGING INFORMATION 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) MAX. TYP. 0.010 (0.25) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES ...
Page 15
X24C08 PACKAGING INFORMATION 14-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX PIN 1 (4X) 7 0.050 (1.27) 0 – 8 NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES ...
Page 16
... LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. ...