BT8370KPF

Manufacturer Part NumberBT8370KPF
DescriptionFully integrated T1/E1 framer and line interface
ManufacturerConexant Systems, Inc.
BT8370KPF datasheet
 


Specifications of BT8370KPF

CaseQFP  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
Page 221
222
Page 222
223
Page 223
224
Page 224
225
Page 225
226
Page 226
227
Page 227
228
Page 228
229
Page 229
230
Page 230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
Page 226/323

Download datasheet (3Mb)Embed
PrevNext
3.16 Data Link Registers
0B6— TDL #2 FIFO Empty Control (TDL2_FEC)
Not available in Bt8376 device.
NOTE:
7
6
5
FEC[5]
Near Empty Transmit FIFO Threshold—Selects a FIFO depth of near empty interrupt
FEC[5:0]
[TNEAR; addr 00A] and near empty level status [TNEAR2; addr 0B9]. The TNEAR interrupt
is activated when the number of data bytes remaining to be transmitted from the FIFO falls
below the selected threshold. The TNEAR2 indicator is active as long as the number of
processor-filled FIFO locations is below the selected threshold. Thus, TNEAR2 is active-high
when the transmit FIFO is completely empty. It remains active until the processor writes the
selected threshold number of bytes to TDL2 [addr 0B8].
Assuming the processor writes 64 bytes to fill an empty FIFO, the TNEAR interrupt occurs
after the transmitter has sent the number of bytes required to bring the FIFO level below the
selected threshold. Hence, the processor is guaranteed to consecutively write 64 – FEC[5:0]
number of bytes to the transmit FIFO in response to a TNEAR interrupt. The interrupt signifies
time remaining (in bytes) for the processor to write TDL2 before the transmit FIFO is emptied.
Typically, FEC[5:0] is set to a small value (approximately 5- to 10-byte threshold) minimize
the number of TNEAR interrupts and to maximize the time between TNEAR interrupts.
FEC[5:0]
0B7— TDL #2 End Of Message Control (TDL2_EOM)
Not available in Bt8376 device.
NOTE:
7
6
5
End of Transmit Message—Writing any data value to TDL2_EOM marks the last byte of data
TDL2_EOM
written into the transmit FIFO as the end of an HDLC message (FCS or Non-FCS mode), or
end of a transmit circular buffer. The processor must write TDL2_EOM after writing a
complete message, or after writing the last byte of a circular buffer into TDL2 [addr 0B8]. The
written data value is ignored and cannot be read back. Multiple HDLC messages are allowed
to be queued in the transmit FIFO simultaneously. Transition from one circular buffer to
another occurs only after the current circular buffer has been sent.
3-108
Fully Integrated T1/E1 Framer and Line Interface
4
3
FEC[4]
FEC[3]
Byte threshold @ TNEAR
00 0000
disabled
00 0001
1-byte threshold
00 0010
2-byte threshold
|
|
11 1110
62-byte threshold
11 1111
63-byte threshold
4
3
Conexant
Bt8370/8375/8376
2
1
0
FEC[2]
FEC[1]
FEC[0]
Empty @ TNEAR
disabled
63 empty
62 empty
|
2 empty
1 empty
2
1
0
N8370DSE