MC68HC705C8ACS

Manufacturer Part NumberMC68HC705C8ACS
ManufacturerFreescale Semiconductor, Inc
MC68HC705C8ACS datasheet
 


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Page 111
112
Page 112
113
Page 113
114
Page 114
115
Page 115
116
Page 116
117
Page 117
118
Page 118
119
Page 119
120
Page 120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
Page 111/222:

PROM Programming Routines

Download datasheet (3Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
9.4 PROM Programming Routines
This subsection describes the routines necessary to program, verify, and
secure the PROM device, and other routines available to the user.
9.4.1 Program and Verify PROM
The program and verify PROM routine copies the contents of the
external EPROM into the MCU PROM with direct correspondence
between the addresses. Memory addresses in the MCU that are not
implemented in PROM are skipped. Unprogrammed addresses in the
EPROM being copied should contain $00 bytes to speed up the
programming process.
To run the program and verify the PROM routine on the PROM MCU,
take these steps:
1. Set switch 1 in the ON position (restores V
2. Restore the V
3. Set switches S3, S4, S5, and S6 in the OFF position (selects
4. Set switch 2 in the OUT position (routine is activated).
5. Set switch 2 in the RESET position.
At this point, if no other MCU is to be programmed or secured, remove
V
power from the board. If another routine is to be performed on the
PP
MCU being programmed, the user can then set switches S3, S4, S5, and
S6 to the positions necessary to select the next routine, and begin the
routine by setting switch 2 to the OUT position. If no other routine is to
be performed, remove V
the programming socket.
MC68HC705C8A — Rev. 3
MOTOROLA
For More Information On This Product,
power source.
PP
proper routine).
The red light-emitting diode (LED) is illuminated, showing that the
programming part of the routine is running. The LED goes out
when programming is finished. The verification part of the routine
now begins. When the green LED is illuminated, verification is
successfully completed and the routine is finished.
from the board and remove the MCU from
DD
EPROM/OTPROM (PROM)
Go to: www.freescale.com
EPROM/OTPROM (PROM)

PROM Programming Routines

).
DD
Technical Data