MC68HC705C8ACS

Manufacturer Part NumberMC68HC705C8ACS
ManufacturerFreescale Semiconductor, Inc
MC68HC705C8ACS datasheet
 


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
Page 141
142
Page 142
143
Page 143
144
Page 144
145
Page 145
146
Page 146
147
Page 147
148
Page 148
149
Page 149
150
Page 150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
Page 144/222

Download datasheet (3Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI)
11.4.2 Pin Functions in Slave Mode
Clearing the MSTR bit in the SPCR configures the SPI for operation in
slave mode. The slave-mode functions of the SPI pins are:
When CPHA = 0, the shift clock is the OR of SS with SCK. In this clock
phase mode, SS must go high between successive characters in an SPI
message. When CPHA = 1, SS may be left low for several SPI
characters. In cases with only one SPI slave MCU, the slave MCU SS
line can be tied to V
The WCOL flag bit can be improperly set when attempting the first
transmission after a reset if these conditions are present: MSTR = 0,
CPOL = 0, CPHA = 1, SS pin = 0, and SCK pin = 1. The reset states of
the CPOL and CPHA bits are 0 and 1, respectively. Under normal
operating conditions (CPOL = 0, CPHA = 1), the SCK input will be low.
The incorrect setting of the WCOL bit can be prevented in two ways:
1. Send a dummy transmission after reset, clear the WCOL flag, and
2. Use the MSTR bit in the SPCR (SPI control register). This is
Technical Data
144
PD4/SCK (serial clock) — In slave mode, the PD4/SCK pin is the
input for the synchronizing clock signal from the master SPI.
PD3/MOSI (master output, slave input) — In slave mode, the
PD3/MOSI pin is the serial input.
PD2/MISO (master input, slave output) — In slave mode, the
PD2/MISO pin is the serial output.
PD5/SS (slave select) — In slave mode, the PD5/SS pin enables
the SPI for data and serial clock reception from a master SPI.
as long as CPHA = 1 clock modes are used.
SS
then proceed with the real transmission.
accomplished by setting the MSTR bit at the same time the CPOL
and CPHA bits are programmed to the desired logic levels. Then,
the data register can be written to if desired. After this, the MSTR
bit should be set to a logic 0, the SPE (SPI enable bit) should be
set to a logic 1, and the CPOL, CPHA, SPR1, and SPR0 bits set
to the desired logic levels. If this procedure is followed after a reset
and before the first access to the SPDR, the WCOL flag will not be
set.
Serial Peripheral Interface (SPI)
For More Information On This Product,
Go to: www.freescale.com
MC68HC705C8A — Rev. 3