MC68HC705C8ACS

Manufacturer Part NumberMC68HC705C8ACS
ManufacturerFreescale Semiconductor, Inc
MC68HC705C8ACS datasheet
 


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
Page 141
142
Page 142
143
Page 143
144
Page 144
145
Page 145
146
Page 146
147
Page 147
148
Page 148
149
Page 149
150
Page 150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
Page 148/222:

SPI Interrupts

Download datasheet (3Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI)
11.7.3 Overrun Error
Failing to read the byte in the SPDR before a subsequent byte enters the
shift register causes an overrun condition. In an overrun condition, all
incoming data is lost until software clears SPIF. The overrun condition
has no flag.
11.8 SPI Interrupts
The SPIF bit in the SPSR indicates a byte has shifted into or out of the
SPDR. The SPIF bit is a source of SPI interrupt requests. The SPI
interrupt enable bit (SPIE) in the SPCR is the local mask for SPIF
interrupts.
The MODF bit in the SPSR indicates a mode error and is a source of SPI
interrupt requests. The MODF bit is set when a logic 0 occurs on the
PD5/SS pin while the MSTR bit is set. The SPI interrupt enable bit (SPIE)
in the SPCR is the local mask for MODF interrupts.
11.9 SPI I/O Registers
These input/output (I/O) registers control and monitor SPI operation:
Technical Data
148
– CPHA = 1 — A slave SPI can cause a write collision error by
writing to the SPDR while receiving a transmission, that is,
between the first active SCK edge and the end of the eighth
SCK cycle. The error does not affect the transmission from the
master SPI, but the byte that caused the error is lost.
SPI data register (SPDR)
SPI control register (SPCR)
SPI status register (SPSR)
Serial Peripheral Interface (SPI)
For More Information On This Product,
Go to: www.freescale.com
MC68HC705C8A — Rev. 3