M52348SP MITSUBISHI, M52348SP Datasheet
M52348SP
Available stocks
Related parts for M52348SP
M52348SP Summary of contents
Page 1
... DESCRIPTION The M52348SP is an semiconductor IC for RGBHV interface that switches signals input from two types of image source and outputs them to CRT display etc. The synchronous signal meets the frequency band of 10 kHz to 200 kHz and is output with TTL. The IC adopts 250 MHz for the frequency band width of video signal, providing high resolution images ...
Page 2
... Takes ratio of the values above abb SG4 Takes ratio of the values above abb bab bba SG5 SG5 SG5 - - - abb SG5 MITSUBISHI ICs (Monitor) M52348SP Unit V mW ˚C ˚ Limits SW12 SW14 SW15 SW16 SW17 Min. Gin2 Bin2 Hin2 Vin2 Swich GND ...
Page 3
... SG7 SG7 - - SG1 SG1 SG1 SG7 SG7 - - SG1 SG1 MITSUBISHI ICs (Monitor) M52348SP SW Limits SW14 SW15 SW16 SW17 Min. Typ. Bin2 Hin2 Vin2 Swich GND - OPEN OPEN bba -60 SG3 - - GND GND - OPEN OPEN bba -40 SG4 - - GND - GND bba ...
Page 4
... Assign SW17 to OPEN and then input SG3 into pin . Measure the output amplitude of T.P.31 at that time and specify V2 the value Assign SW17 to GND and then measure the output amplitude of T.P.31 at that time. Specify the value MITSUBISHI ICs (Monitor) M52348SP , and G , fi ...
Page 5
... P-P Table. Assign SW17 to GND (or OPEN), input SG7 into the input pin and measure the output waveform. only. 14 Rising delay time Trd1 (Trd2) and falling delay time Tfd1 (Tfd2) shall be found according to the following diagram. MITSUBISHI ICs (Monitor) M52348SP 100% 90% 10 ...
Page 6
... WIDE FREQUENCY BAND ANALOG SWITCH TYPICAL CHARACTERISTICS THERMAL DERATING (MAXIMUM RATING) 2000 , and . Input 1603 1600 1200 , specify the output at 17 800 , and and 400 , specify the output at 17 0.7V P-P ) P-P ) P-P ) P MITSUBISHI ICs (Monitor) M52348SP - 100 125 150 AMBIENT TEMPERATURE Ta (˚C) 6 ...
Page 7
... TEST CIRCUIT 0.01 7 MITSUBISHI ICs (Monitor) WIDE FREQUENCY BAND ANALOG SWITCH TP6 0.01 TP4 0.01 0.01 TP2 0.01 M52348SP Units Reslstance : Capacitance : F ...
Page 8
... INPUT1(B) 6 INPUT1(H) 7 INPUT1( GND INPUT2(R) 10 INPUT2(G) 12 INPUT2(B) 14 WIDE FREQUENCY BAND ANALOG SWITCH DC voltage Peripheral circuit of pins 1.0mA 0.2mA 1.0mA MITSUBISHI ICs (Monitor) M52348SP Description of function (V) 5.0 Input at low impedance. 2.0 Input pulse more and 5V or less GND Input at low impedance. 2.0 8 ...
Page 9
... WIDE FREQUENCY BAND ANALOG SWITCH Peripheral circuit of pins 0.2mA 7.3k 2. 430 500 , MITSUBISHI ICs (Monitor) M52348SP DC voltage Description of function (V) Input pulse more and 5V or less Enables switching between OPEN and GND. 2.6 Contains output resistance. - Apply the same voltage. 5.0 - Contains output resistance. ...
Page 10
... Insertion of a resistance of several tens of pin and the circuit at the next stage makes oscillation harder. • GND should be as wide as possible. Basically, solid earth should 5V be used. R and ) are as shown more. MITSUBISHI ICs (Monitor) M52348SP between the output 10 ...