MC68HC708MP16CFU

Manufacturer Part NumberMC68HC708MP16CFU
ManufacturerFreescale Semiconductor, Inc
MC68HC708MP16CFU datasheet
 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
Page 141
142
Page 142
143
Page 143
144
Page 144
145
Page 145
146
Page 146
147
Page 147
148
Page 148
149
Page 149
150
Page 150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
Page 144/398:

Dead-Time Insertion

Download datasheet (4Mb)Embed
PrevNext
Pulse Width Modulator for Motor Control (PWMMC)
When complementary operation is used, two additional features are
provided:
If independent operation is chosen, each PWM has its own PWM value
register.
9.6.2 Dead-Time Insertion
As shown in
be used to drive top-side/bottom-side transistors.
When controlling DC-to-AC inverters such as this, the top and bottom
PWMs in one pair should never be active at the same time. In
12, if PWM1 and PWM2 were on at the same time, large currents would
flow through the two transistors as they discharge the bus capacitor. The
IGBTs could be weakened or destroyed.
Simply forcing the two PWMs to be inversions of each other is not always
sufficient. Since a time delay is associated with turning off the transistors
in the motor drive, there must be a “dead-time” between the deactivation
of one PWM and the activation of the other.
A dead-time can be specified in the dead-time write-once register. This
8-bit value specifies the number of CPU clock cycles to use for the dead-
time. The dead-time is not affected by changes in the PWM period
caused by the prescaler.
Dead-time insertion is achieved by feeding the top PWM outputs of the
PWM generator into dead-time generators, as shown in
Current sensing determines which PWM value of a PWM generator pair
to use for the TOP PWM in the next PWM cycle. (See
Correction.) When output control is enabled, the odd OUT bits, rather
than the PWM generator outputs, are fed into the dead-time generators.
(See
9.6.5 Output Port
Technical Data
144
Pulse Width Modulator for Motor Control (PWMMC)

Dead-time insertion

Separate top/bottom pulse width correction to correct for
distortions caused by the motor drive characteristics.
Figure
9-12, in complementary mode, each PWM pair can
Control.)
Figure 9-
Figure
9-13.
9.6.3 Top/Bottom
MC68HC708MP16
Rev. 3.1
Freescale Semiconductor