MX29F002NTQC-90 Macronix International Co., MX29F002NTQC-90 Datasheet
MX29F002NTQC-90
Available stocks
Related parts for MX29F002NTQC-90
MX29F002NTQC-90 Summary of contents
Page 1
FEATURES • 262,144x 8 only • Fast access time: 55/70/90/120ns • Low power consumption - 30mA maximum active current(5MHz) - 1uA typical standby current • Programming and erasing voltage 5V ± 10% • Command register architecture - Byte Programming (7us ...
Page 2
PIN CONFIGURATIONS 32 PDIP NC on MX29F002NT/B RESET 1 A16 2 A15 3 A12 GND 16 32 ...
Page 3
BLOCK DIAGRAM CONTROL WE INPUT OE LOGIC WP RESET ADDRESS LATCH A0~A17 AND BUFFER Q0-Q7 P/N: PM0547 MX29F002/002N T/B PROGRAM/ERASE HIGH VOLTAGE MX29F002 FLASH ARRAY ARRAY SOURCE HV Y-PASS GATE PGM SENSE DATA AMPLIFIER HV PROGRAM DATA LATCH I/O BUFFER ...
Page 4
AUTOMATIC PROGRAMMING The MX29F002T/B is byte programmable using the Automatic Programming algorithm. The Automatic Programming algorithm does not require the system to time out or verify the data programmed. The typical chip programming time of the MX29F002T/B at room temperature ...
Page 5
TABLE 1. SOFTWARE COMMAND DEFINITIONS First Bus Command Bus Cycle Addr Data Reset 1 XXXH F0H Read 1 RA Read Silicon ID 4 555H AAH Sector Protect 4 555H AAH Verification Program 4 555H AAH Chip Erase 6 555H AAH ...
Page 6
TABLE 2. MX29F002T/B BUS OPERATION Pins Mode Read Silicon ID Manufacturer Code(1) Read Silicon ID Device Code(1) Read Standby Output Disable Write Sector Protect with 12V system(6) Chip Unprotect with 12V system(6) Verify Sector Protect with 12V system Sector Protect ...
Page 7
READ/RESET COMMAND The read or reset operation is initiated by writing the read/ reset command sequence into the command register. Microprocessor read cycles retrieve array data. The device remains enabled for reads until the command register contents are altered. If ...
Page 8
SET-UP AUTOMATIC SECTOR COMMANDS The Automatic Sector Erase does not require the device to be entirely pre-programmed prior to executing the Automatic Set-up Sector Erase command and Automatic Sector Erase command. Upon executing the Automatic Sector Erase command, the device ...
Page 9
TABLE 4. WRITE OPERATION STATUS Status Byte Program in Auto Program Algorithm Auto Erase Algorithm In Progress Erase Suspended Mode Byte Program in Auto Program Algorithm Exceeded Auto Erase Algorithm Time Limits Erase Suspend Program Note and Q2 ...
Page 10
ERASE RESUME This command will cause the command register to clear the suspend state and return back to Sector Erase mode but only if an Erase Suspend command was previously issued. Erase Resume will not have any effect in all ...
Page 11
Q2:Toggle Bit II The "Toggle Bit II" on Q2, when used with Q6, indicates whether a particular sector is actively erasing (that is, the Automatic Erase algorithm is in process), or whether that sector is erase-suspended. Toggle Bit I is ...
Page 12
Q3 Sector Erase Timer After the completion of the initial sector erase command sequence the sector erase time-out will begin. Q3 will remain low until the time-out is complete. Data Polling and Toggle Bit are valid after the initial sector ...
Page 13
Temporary Sector Unprotect Operation (For 29F002T/B only) Temporary Sector Unprotect Completed(Note 2) Note : P/N: PM0547 MX29F002/002N T/B Start RESET = VID (Note 1) Perform Erase or Program Operation Operation Completed RESET = VIH 1. All protected sectors are temporary ...
Page 14
TEMPORARY SECTOR UNPROTECT Parameter Std. Description tVIDR VID Rise and Fall Time (See Note) tRSP RESET Setup Time for Temporary Sector Unprotect Note: Not 100% tested Temporary Sector Unprotect Timing Diagram 12V RESET tVIDR CE WE P/N: ...
Page 15
AC CHARACTERISTICS Parameter Std Description tREADY RESET PIN Low (Not During Automatic Algorithms) to Read or Write (See Note) tRP1 RESET Pulse Width (During Automatic Algorithms) tRP2 RESET Pulse Width (NOT During Automatic Algorithms) MIN tRH RESET High Time Before ...
Page 16
CHIP UNPROTECT WITH 12V SYSTEM The MX29F002T/B also features the chip unprotect mode, so that all sectors are unprotected after chip unprotect is completed to incorporate any changes in the code recommended to protect all sectors before activating ...
Page 17
DC/AC Operating Conditions for Read/Programming/Erase Operation Operating Temperature Vcc Power Supply o CAPACITANCE 1.0 MHz SYMBOL PARAMETER CIN1 Input Capacitance CIN2 Control Pin Capacitance COUT Output Capacitance READ OPERATION DC CHARACTERISTICS SYMBOL PARAMETER ILI ...
Page 18
AC CHARACTERISTICS SYMBOL PARAMETER tACC Address to Output Delay tCE CE to Output Delay tOE OE to Output Delay tDF OE High to Output Float tOH Address to Output hold SYMBOL PARAMETER tACC Address to Output Delay tCE CE to ...
Page 19
COMMAND PROGRAMMING/DATA PROGRAMMING/ERASE OPERATION DC CHARACTERISTICS SYMBOL PARAMETER ICC1 (Read) Operating VCC Current ICC2 ICC3 (Program) ICC4 (Erase) ICCES VCC Erase Suspend Current NOTES: 1. VIL min. = -0.6V for pulse width is equal to or less than 20ns. 2. ...
Page 20
AC CHARACTERISTICS SYMBOL PARAMETER tOES OE setup time tCWC Command programming cycle tCEP WE programming pulse width tCEPH1 WE programming pulse width High tCEPH2 WE programming pulse width High tAS Address setup time tAH Address hold time tDS Data setup ...
Page 21
AC CHARACTERISTICS SYMBOL PARAMETER tOES OE setup time tCWC Command programming cycle tCEP WE programming pulse width tCEPH1 WE programming pulse width High tCEPH2 WE programming pulse width High tAS Address setup time tAH Address hold time tDS Data setup ...
Page 22
SWITCHING TEST CIRCUITS DEVICE UNDER SWITCHING TEST WAVEFORMS(I) for speed grade 70ns max. 2.4V 0.45V SWITCHING TEST WAVEFORMS(II) for speed grade 55ns(MX29F002T/B-55) 3. TESTING: Inputs are driven at 3.0V for a logic "1" and 0V for a logic ...
Page 23
COMMAND WRITE TIMING WAVEFORM VCC 5V VIH ADD A0~17 VIL tAS VIH WE VIL tOES CE VIH VIL OE VIH VIL VIH DATA Q0-7 VIL P/N: PM0547 MX29F002/002N T/B ADD Valid tAH tCEP tCWC tCS tCH tDS tDH DIN 23 ...
Page 24
AUTOMATIC PROGRAMMING TIMING WAVEFORM One byte data is programmed. Verify in fast algorithm and additional programming by external control are not required because these operations are executed automatically by internal control circuit. Programming completion can be AUTOMATIC PROGRAMMING TIMING WAVEFORM ...
Page 25
AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data A0H Address 555H Write Program Data/Address Toggle Bit Checking Q6 not Toggled NO Invalid Verify Byte Ok Command Auto Program Completed P/N: PM0547 MX29F002/002N ...
Page 26
TOGGLE BIT ALGORITHM P/N: PM0547 MX29F002/002N T/B START Read Q7~Q0 Read Q7~Q0 (Note 1) NO Toggle Bit Q6 =Toggle? YES NO Q5=1? YES Read Q7~Q0 Twice (Note 1,2) Toggle Bit Q6 =Toggle? YES Program/Erase Operation Not Program/Erase Operation Complete Complete, ...
Page 27
AUTOMATIC CHIPE RASETIMING WAVEFORM All data in chip are erased. External erase verify is not required because data is erased automatically by internal control circuit. Erasure completion can be verified by DATA polling and toggle bit checking after automatic erase ...
Page 28
AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART Invalid Command P/N: PM0547 MX29F002/002N T/B START Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 80H Address 555H Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 10H ...
Page 29
AUTOMATIC SECTOR ERASE TIMING WAVEFORM Sector data indicated by A13 to A17 are erased. External erase verification is not required because data are erased automatically by internal control circuit. Erasure comple- tion can be verified by DATA polling and toggle ...
Page 30
AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 80H Address 555H Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 30H Sector Address Load Other Sector Addrss If ...
Page 31
ERASE SUSPEND/ERASE RESUME FLOWCHART . P/N: PM0547 MX29F002/002N T/B START Write Data B0H NO Toggle Bit checking Q6 not toggled YES Read Array or Program Reading or NO Programming End YES Write Data 30H Continue Erase . Another NO Erase ...
Page 32
TIMING WAVEFORM FOR SECTOR PROTECTION FOR SYSTEM WITH 12V A1 A6 12V 5V A9 tVLHT 12V 5V OE tVLHT WE CE Data A17-A13 P/N: PM0547 MX29F002/002N T/B tWPP 1 tOESP Sector Address 32 Verify tVLHT 01H F0H tOE REV. 1.5, ...
Page 33
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITH 12V A1 12V 5V A9 tVLHT A6 12V 5V OE tVLHT WE CE Data P/N: PM0547 MX29F002/002N T/B tWPP 2 tOESP 33 Verify tVLHT 00H F0H tOE REV. 1.5, MAR. 28, 2005 ...
Page 34
SECTOR PROTECTION ALGORITHM FOR SYSTEM WITH 12V No PLSCNT=32? Yes Device Failed P/N: PM0547 MX29F002/002N T/B START Set Up Sector Addr (A17,A16,A15,A14,A13) PLSCNT=1 OE=VID,A9=VID,CE=VIL A6=VIL Activate WE Pulse Time Out 10us Set WE=VIH, CE=OE=VIL A9 should remain VID Read from ...
Page 35
CHIP UNPROTECTION ALGORITHM FOR SYSTEM WITH 12V Increment Sector Addr * It is recommended before unprotect the whole chip, all sectors should be protected in advance. P/N: PM0547 MX29F002/002N T/B START Protect All Sectors PLSCNT=1 Set OE=A9=VID CE=VIL,A6=1 Activate WE ...
Page 36
TIMING WAVEFORM FOR SECTOR PROTECTION FOR SYSTEM WITHOUT 12V Data Don't care (Note 2) A17-A13 Note1: Must issue "unlock for sector protect/unprotect" command before sector protection for a system without 12V provided. Note2: Except ...
Page 37
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITHOUT 12V Data Don't care Note1: Must issue "unlock for sector protect/unprotect" command before sector unprotection for a system without 12V provided. Note2: Except F0H P/N: PM0547 ...
Page 38
SECTOR PROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V Increment PLSCNT No PLSCNT=32? Yes Device Failed P/N: PM0547 MX29F002/002N T/B START PLSCNT=1 Write "unlock for sector protect/unprotect" Command(Table1) Set Up Sector Addr (A17,A16,A15,A14,A13) OE=VIH,A9=VIH CE=VIL,A6=VIL Activate WE Pulse to start Data don't ...
Page 39
CHIP UNPROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V Increment Sector Addr * It is recommended before unprotect the whole chip, all sectors should be protected in advance. P/N: PM0547 MX29F002/002N T/B START Protect All Sectors PLSCNT=1 Write "unlock for sector protect/unprotect" ...
Page 40
ID CODE READ TIMING WAVEFORM MODE VCC 5V VID ADD VIH A9 VIL ADD AD A1 VIH VIL ADD VIH A2-A8 A10-A17 VIL CE VIH VIL VIH WE VIL VIH OE VIL VIH DATA VIL Q0-Q7 P/N: PM0547 MX29F002/002N T/B ...
Page 41
ORDERING INFORMATION PLASTIC PACKAGE PART NO. Access Time (ns) MX29F002TPC-55 55 MX29F002TPC-70 70 MX29F002TPC-90 90 MX29F002TPC-12 120 MX29F002TTC-55 55 MX29F002TTC-70 70 MX29F002TTC-90 90 MX29F002TTC-12 120 MX29F002TQC-55 55 MX29F002TQC-70 70 MX29F002TQC-90 90 MX29F002TQC-12 120 MX29F002BPC-55 55 MX29F002BPC-70 70 MX29F002BPC-90 90 MX29F002BPC-12 ...
Page 42
... PART NO. Access Time (ns) MX29F002NTTC-70 70 MX29F002NTTC-90 90 MX29F002NTTC-12 120 MX29F002NTQC-55 55 MX29F002NTQC-70 70 MX29F002NTQC-90 90 MX29F002NTQC-12 120 MX29F002NBPC-55 55 MX29F002NBPC-70 70 MX29F002NBPC-90 90 MX29F002NBPC-12 120 MX29F002NBTC-55 55 MX29F002NBTC-70 70 MX29F002NBTC-90 90 MX29F002NBTC-12 120 MX29F002NBQC-55 55 MX29F002NBQC-70 70 MX29F002NBQC-90 90 MX29F002NBQC-12 120 MX29F002TPI-70 70 MX29F002TPI-90 90 MX29F002TPI-12 120 MX29F002TTI-70 70 MX29F002TTI-90 90 MX29F002TTI-12 120 IMX29F002TQI-70 70 MX29F002TQI-90 90 MX29F002TQI-12 120 IMX29F002BPI-70 70 MX29F002BPI-90 ...
Page 43
PART NO. Access Time (ns) IMX29F002BTI-70 70 MX29F002BTI-90 90 MX29F002BTI-12 120 MX29F002BQI-70 70 MX29F002BQI-90 90 MX29F002BQI-12 120 MX29F002NTPI-70 70 MX29F002NTPI-90 90 MX29F002NTPI-12 120 MX29F002NTTI-70 70 MX29F002NTTI-90 90 MX29F002NTTI-12 120 MX29F002NTQI-70 70 MX29F002NTQI-90 90 MX29F002NTQI-12 120 MX29F002NBPI-70 70 MX29F002NBPI-90 90 MX29F002NBPI-12 ...
Page 44
PART NO. Access Time (ns) MX29F002TTC-70G 70 MX29F002TTC-90G 90 MX29F002BTC-70G 70 MX29F002BTC-90G 90 MX29F002TQC-70G 70 MX29F002TQC-90G 90 MX29F002BQC-70G 70 MX29F002BQC-90G 90 MX29F002TPC-70G 70 MX29F002TPC-90G 90 MX29F002BPC-70G 70 MX29F002BPC-90G 90 MX29F002TPI-70G 70 MX29F002TPI-90G 90 MX29F002BPI-70G 70 MX29F002BPI-90G 90 P/N: PM0547 MX29F002/002N ...
Page 45
... PART NO. Access Time (ns) MX29F002NTTC-70G 70 MX29F002NTTC-90G 90 MX29F002NBTC-70G 70 MX29F002NBTC-90G 90 MX29F002NTQC-70G 70 MX29F002NTQC-90G 90 MX29F002NBQC-70G 70 MX29F002NBQC-90G 90 MX29F002NTPC-70G 70 MX29F002NTPC-90G 90 MX29F002NBPC-70G 70 MX29F002NBPC-90G 90 P/N: PM0547 MX29F002/002N T/B Operating Current Standby Current (mA) MAX.(uA Temperature PACKAGE Range C~ Pin TSOP ...
Page 46
ERASE AND PROGRAMMING PERFORMANCE(1) PARAMETER Sector Erase Time Chip Erase Time Byte Programming Time Chip Programming Time Erase/Program Cycles Note: 1.Not 100% Tested, Excludes external system level over head. 2.Typical values measured 5V. 3.Maximum values measured at ...
Page 47
PACKAGE INFORMATION P/N: PM0547 MX29F002/002N T/B 47 REV. 1.5, MAR. 28, 2005 ...
Page 48
P/N: PM0547 MX29F002/002N T/B 48 REV. 1.5, MAR. 28, 2005 ...
Page 49
P/N: PM0547 MX29F002/002N T/B 49 REV. 1.5, MAR. 28, 2005 ...
Page 50
REVISION HISTORY Revision Description 1.0 1.Removed "Advanced Information" datasheet marking and contain information on products in full production 2.The modification summary of Revision 0.9.8 to Revision 1.0: 2-1.Program/erase cycle times:10K cycles-->100K cycles 2-2.To add data retention 20 years 2-3.To add ...
Page 51
... MX29F002/002N T/B MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. ...