MC54HC4052J Motorola, MC54HC4052J Datasheet
MC54HC4052J
Related parts for MC54HC4052J
MC54HC4052J Summary of contents
Page 1
... MULTIPLEXER/ X3 INPUTS/ 1 DEMULTIPLEXER OUTPUTS CHANNEL 10 B SELECT 9 INPUTS C 6 ENABLE PIN PIN PIN 8 = GND 10/95 Motorola, Inc. 1995 3 COMMON X OUTPUT/ INPUT Pinout: MC54/74HC4051 (Top View ...
Page 2
... A 10 CHANNEL-SELECT B INPUTS ENABLE NOTE: This device allows independent control of each switch. Channel–Select Input A controls the X–Switch, Input B controls the Y–Switch and Input C controls the Z–Switch MOTOROLA FUNCTION TABLE – MC74HC4052 Control Inputs Enable COMMON H OUTPUTS/INPUTS X = Don’ ...
Page 3
... SOIC Package: – from 125 _ C TSSOP Package: – 6.1 mW from 125 _ C For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î ...
Page 4
... I in Maximum Input Leakage Current, Channel–Select or Enable Inputs I CC Maximum Quiescent Supply Current (per Package) NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). DC CHARACTERISTICS — Analog Section Symbol Symbol Parameter Parameter R on Maximum “ ...
Page 5
... Maximum Input Capacitance, Channel–Select or Enable Inputs C I/O Maximum Capacitance (All Switches Off) NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the Motorola High– Speed CMOS Data Book (DL129/D Power Dissipation Capacitance (Figure 13)* Power Dissipation Capacitance (Figure 13)* * Used to determine the no– ...
Page 6
... Switches (Figure 12) (Test does not apply to HC4051) THD Total Harmonic Distortion (Figure 14) * Limits not tested. Determined by design and verified by qualification. MOTOROLA (GND = 0 V) Condition Condition 1MHz Sine Wave; Adjust f in Voltage to Obtain 0dBm Increase f in Frequency Obtain 0dBm Increase f in Frequency Until dB Meter Reads – ...
Page 7
... Figure 1d. Typical On Resistance – 9.0 V 125 C PROGRAMMABLE POWER 25 C SUPPLY – + – ANALOG IN GND Figure 2. On Resistance Test Set–Up 7 125 – 1.5 2.0 2.5 3.0 3.5 4.0 4.5 125 – 3.0 4.0 5.0 6.0 7.0 8.0 9.0 PLOTTER MINI COMPUTER DC ANALYZER V CC DEVICE UNDER TEST COMMON OUT V EE MOTOROLA ...
Page 8
... OFF CHANNEL SELECT *Includes all probe and jig capacitance Figure 7. Off Channel Feedthrough Isolation, Test Set–Up MOTOROLA COMMON O Figure 4. Maximum Off Channel Leakage Current, Common Channel, Test Set– 0.1 F ...
Page 9
... CHANNEL SELECT *Includes all probe and jig capacitance COMMON O/I TEST ON POINT *Includes all probe and jig capacitance POSITION 1 WHEN TESTING t PHZ AND t PZH POSITION 2 WHEN TESTING t PLZ AND t PZL TEST ON/OFF POINT ENABLE MOTOROLA ...
Page 10
... V CC and ten volts. Therefore, using the configuration of Figure 15, a maximum analog sig- nal of ten volts peak–to–peak can be controlled. Unused analog inputs/outputs may be left floating (i.e., not con- nected). However, tying unused analog inputs and outputs to MOTOROLA V OS ANALOG I ...
Page 11
... Figure 18. Function Diagram, HC4051 ON/OFF Schottky Clipping Diodes +5V 16 +5V ANALOG ON/OFF SIGNAL SIGNAL LSTTL/NMOS 7 10 CIRCUITRY 8 9 HCT BUFFER b. Using HCT Interface MOTOROLA ...
Page 12
... MC54/74HC4051 MC74HC4052 MC54/74HC4053 10 LEVEL A SHIFTER 9 LEVEL B SHIFTER 6 LEVEL ENABLE SHIFTER 11 LEVEL A SHIFTER 10 LEVEL B SHIFTER 9 LEVEL C SHIFTER 6 LEVEL ENABLE SHIFTER MOTOROLA Figure 19. Function Diagram, HC4052 Figure 20. Function Diagram, HC4053 ...
Page 13
... PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS INCHES DIM MIN MAX MIN MAX F A 0.386 0.393 9.80 10.00 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 1.27 BSC 0.050 BSC G J 0.19 0.25 0.008 0.009 K 0.10 0.25 0.004 0.009 0.229 0.244 P 5.80 6.20 R 0.25 0.50 0.010 0.019 MOTOROLA ...
Page 14
... IDENT. 1 0.15 (0.006 –V– C 0.10 (0.004) –T– SEATING D PLANE MOTOROLA OUTLINE DIMENSIONS DW SUFFIX PLASTIC SOIC PACKAGE CASE 751G–02 ISSUE A NOTES: 1. DIMENSIONING AND TOLERANCING 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER ...
Page 15
... Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “ ...