EP910ILI-12

Manufacturer Part NumberEP910ILI-12
ManufacturerAltera Corporation
EP910ILI-12 datasheet
 


Specifications of EP910ILI-12

Dc0201  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
Page 27/42

Download datasheet (729Kb)Embed
PrevNext
Table 17. EP910 & EP910I Device Capacitance
Symbol
Parameter
C
Input pin capacitance
IN
C
I/O pin capacitance
I/O
C
CLK1 pin capacitance
CLK1
C
CLK2 pin capacitance
CLK2
Table 18. EP910 & EP910I Device I
Symbol
Parameter
I
V
supply current
CC1
CC
(non-Turbo, standby)
I
V
supply current
CC2
CC
(non-Turbo, active)
I
V
supply current
CC3
CC
(Turbo, active)
Notes to tables:
(1)
See the
Operating Requirements for Altera Devices Data Sheet
(2)
Numbers in parentheses are for industrial-temperature-range devices.
(3)
The minimum DC input is –0.3 V. During transitions, the inputs may undershoot to –2.0 V (EP910) or
–0.5 V (EP910I) or overshoot to 7.0 V (EP910) or V
less than 20 ns.
(4)
Maximum V
rise time for EP910 devices = 50 ms; for EP910I devices, maximum V
CC
monotonic rise.
(5)
For all clocks: t
and t
= 100 ns (50 ns for the industrial-temperature-range version).
R
F
(6)
These values are specified in
(7)
The device capacitance is measured at 25 C and is sample-tested only.
(8)
The I
parameter refers to high-level TTL or CMOS output current; the I
OH
output current.
(9)
This parameter does not apply to EP910I devices.
(10) When the Turbo Bit option is not set (non-Turbo mode), an EP910 device will enter standby mode if no logic
transitions occur for 100 ns after the last transition, and an EP910I device will enter standby mode if no logic
transitions occur for 75 ns after the last transition.
(11) Measured with a device programmed as a 24-bit counter.
Altera Corporation
Note (6)
Conditions
V
= 0 V, f = 1.0 MHz
IN
V
= 0 V, f = 1.0 MHz
OUT
V
= 0 V, f = 1.0 MHz
IN
V
= 0 V, f = 1.0 MHz
IN
Supply Current
Notes
CC
Conditions
V
= V
or ground, no load
I
CC
(10),
(11)
V
= V
or ground, no load,
I
CC
f = 1.0 MHz (10),
(11)
V
= V
or ground, no load,
I
CC
f = 1.0 MHz
(11)
in this data book.
+ 0.5 V (EP910I) for input currents less than 100 mA and periods
CC
Table 15 on page
770.
Classic EPLD Family Data Sheet
EP910
EP910I
Min
Max
Min
20
20
20
60
(2), (6),
(7)
EP910
EP910I
Min
Typ
Max Min
Typ
20
150
60
6
20
4
45
80
120
(100)
rise time is unlimited with
CC
parameter refers to low-level TTL
OL
Unit
Max
8
pF
8
pF
10
pF
12
pF
Unit
Max
150
µA
12
mA
150
mA
771