TDA7575 STMicroelectronics, TDA7575 Datasheet - Page 15

IC AMP AUDIO 150W AB 27FLEXIWATT

TDA7575

Manufacturer Part Number
TDA7575
Description
IC AMP AUDIO 150W AB 27FLEXIWATT
Manufacturer
STMicroelectronics
Type
Class ABr
Datasheets

Specifications of TDA7575

Output Type
1-Channel (Mono) or 2-Channel (Stereo)
Max Output Power X Channels @ Load
150W x 1 @ 1 Ohm; 75W x 2 @ 2 Ohm
Voltage - Supply
8 V ~ 18 V
Features
Differential Inputs, I²C, Mute, Short-Circuit and Thermal Protection, Standby
Mounting Type
Through Hole
Package / Case
27-Flexiwatt (bent and staggered leads)
Operational Class
Class-AB
Output Power (typ)
150x1@1Ohm/75x2@2OhmW
Audio Amplifier Function
Speaker
Total Harmonic Distortion
0.02@1Ohm@30W%
Single Supply Voltage (typ)
9/12/15V
Dual Supply Voltage (typ)
Not RequiredV
Power Supply Requirement
Single
Power Dissipation
86W
Rail/rail I/o Type
No
Single Supply Voltage (min)
8V
Single Supply Voltage (max)
18V
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Operating Temp Range
-55C to 150C
Operating Temperature Classification
Military
Mounting
Surface Mount
Pin Count
36
Package Type
PSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TDA7575
Manufacturer:
ST
Quantity:
3 089
Part Number:
TDA7575
Manufacturer:
TI
Quantity:
3 090
Part Number:
TDA7575
Manufacturer:
ST
0
Part Number:
TDA7575B
Manufacturer:
ST
0
Part Number:
TDA7575B BC
Manufacturer:
SMD
Quantity:
2
Part Number:
TDA7575B BC
Manufacturer:
ST
0
Part Number:
TDA7575B-BC
Manufacturer:
ST
0
Part Number:
TDA7575B-BC
Manufacturer:
ST
Quantity:
20 000
Part Number:
TDA7575BBC
Manufacturer:
ST
Quantity:
20 000
Part Number:
TDA7575BPD
Manufacturer:
ST
0
Part Number:
TDA7575BPD
Manufacturer:
ST
Quantity:
8 174
Part Number:
TDA7575BPDTR
Manufacturer:
AMD
Quantity:
6 231
Part Number:
TDA7575BPDTR
Manufacturer:
ST
Quantity:
20 000
Part Number:
TDA7575PD
Manufacturer:
ST
Quantity:
2 039
Part Number:
TDA7575PDTR
Manufacturer:
ST
Quantity:
20 000
Part Number:
TDA7575SPD
Manufacturer:
ST
Quantity:
20 000
MULTIPLE FAULTS.
When more misconnections are simultaneously in place at the audio outputs, it is guaranteed that at least one
of them is initially read out. The others are notified after successive cycles of I
provided that the diagnostic is enabled. This is true for both kinds of diagnostic (Turn on and Permanent).
The table below shows all the couples of double-fault possible. It should be taken into account that a short circuit
with the 4 ohm speaker unconnected is considered as double fault.
Double fault table for Turn On Diagnostic
S. GND (so) / S. GND (sk) in the above table make a distinction according to which of the 2 outputs is shorted
to ground (test-current source side= so, test-current sink side = sk). More precisely, in both the Channels SO =
CH+, and SK = CH-.
In Permanent Diagnostic the table is the same, with only a difference concerning Open Load(*) , which is not
among the recognisable faults. Should an Open Load be present during the device's normal working, it would
be detected at a subsequent Turn on Diagnostic cycle (i.e. at the successive Car Radio Turn on).
FAULTS AVAILABILITY
All the results coming from I
period of time. If the fault is stable throughout the whole period, it will be sent out. This is true for DC diagnostic
(Turn on and Permanent), for Offset Detector.
To guarantee always resident functions, every kind of diagnostic cycles (Turn on, Permanent, Offset) will be
reactivate after any I2C reading operation. So, when the micro reads the I
but the read data will come from the previous diag. cycle (i.e. The device is in Turn On state, with a short to Gnd,
then the short is removed and micro reads I2C. The short to Gnd is still present in bytes, because it is the result
of the previous cycle. If another I2C reading operation occurs, the bytes do not show the short). In general to
observe a change in Diagnostic bytes, two I2C reading operations are necessary.
I
A correct turn on/off sequence respectful of the diagnostic timings and producing no audible noises could be as
follows (after battery connection):
Car Radio Installation: DIAG ENABLE (write) --- 200 ms --- I
(repeat I
2
C PROGRAMMING/READING SEQUENCES
– TURN-ON: (STAND-BY OUT + DIAG ENABLE) --- 500 ms (min) --- MUTING OUT
– TURN-OFF: MUTING IN --- 20 ms --- (DIAG DISABLE + STAND-BY IN)
– OFFSET TEST: Device in Play (no signal) --
– OFFSET ENABLE - 30ms - I
S. Across L.
S. GND (sc)
S. GND (sk)
Open L.
S. Vs
2
C reading until high-offset message disappears).
S. GND (sc)
S. GND
/
/
/
/
2
Cbus, by read operations, are the consequence of measurements inside a defined
2
C reading
S. GND (sk)
S. GND
S. GND
/
/
/
S. Vs + S. GND
2
C read (repeat until All faults disappear).
S. Vs
S. Vs
S. Vs
/
/
2
C, a new cycle will be able to start,
S. Across L.
S. Across L.
S. GND
S. GND
2
C reading and faults removal,
S. Vs
/
Open L. (*)
Open L. (*)
Open L.
S. GND
S. Vs
TDA7575
N.A.
15/17

Related parts for TDA7575