JAW050B1 Lineage Power, JAW050B1 Datasheet
JAW050B1
Available stocks
Related parts for JAW050B1
JAW050B1 Summary of contents
Page 1
Data Sheet April 2008 JAW050B and JAW075B Power Modules; dc-dc Converters: 36 Vdc to 75 Vdc Input, 12 Vdc Output The JAW Series Power Modules use surface-mount technol- ogy and deliver efficient and compact dc-dc ...
Page 2
... Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Table 1. Input Specifications Parameter Operating Input Voltage Maximum Input Current max JAW050B1 (See Figure 1.) JAW075B1 (See Figure 2 max JAW050B1 JAW075B1 Inrush Transient Input Reflected-ripple Current, Peak-to-peak ( MHz, 12 µ ...
Page 3
... O * Consult your sales representative or the factory. † These are manufacturing test limits. In some situations, results may differ. Table 3. Isolation Specifications Parameter Isolation Capacitance Isolation Resistance Lineage Power 36 Vdc to 75 Vdc Input, 12 Vdc Output (continued) Device Symbol All V All ...
Page 4
... April 2008 Typ Max 3,000,000 hours — 100 (3.5) g (oz.) Min Typ Max 0 — 1.2 — — 1.0 — — 15 — — 50 — — — 0.5 70 — 110 %V 13.2* — 15.5* — 105 — C Lineage Power Unit Unit µ nom V °C ...
Page 5
... Figure 2. Typical JAW075B1 Input Characteristics at Room Temperature Lineage Power 36 Vdc to 75 Vdc Input, 12 Vdc Output 0.4 (V) I 8-3216 (F).a Figure 3. Typical JAW050B1 Efficiency vs. Output 6. 3.125 0.625 0 (V) I 8-3217 (F) ...
Page 6
... Full Load at Room Temperature and 48 Vdc Input (Waveform Averaged to Eliminate Ripple Component.) 2.1 A 8-3221 (F).a Note: Tested without any load capacitance. Figure 8. Typical JAW050B1 Transient Response to Step Decrease in Load from 50% to 25% of Full Load at Room Temperature and 48 Vdc Input (Waveform Averaged to Eliminate Ripple Component.) April 2008 TIME, t (50 μ ...
Page 7
... TIME, t (20 ms/div) Note: Tested without any load capacitance. Figure 10. JAW075B1 Typical Start-Up from Remote On/Off Lineage Power 36 Vdc to 75 Vdc Input, 12 Vdc Output Test Configurations BATTERY Note: Measure input reflected-ripple current with a simulated source inductance (L tery impedance. Measure current as shown above. ...
Page 8
... V on/off If not using the remote on/off feature, do one of the following: For negative logic, short the ON/OFF pin For positive logic, leave the ON/OFF pin open. n April 2008 ). The on/off generated by on/off = µA. (–). I Lineage Power ...
Page 9
... Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power. Lineage Power 36 Vdc to 75 Vdc Input, 12 Vdc Output SUPPLY CONTACT ...
Page 10
... Note: Top view, pin locations are for reference only. Measurements shown are in millimeters and (inches). Figure 18. Case Temperature Measurement April 2008 V (+) V (+) I O ON/OFF + SEN TRIM CASE – SEN V (–) V (– MEASURE CASE TEMPERATURE HERE 14.2 (0.56) Location Lineage Power ) C 8-3228 (F) ...
Page 11
... Determine airflow (v) (Use Figure 21.): v = 1.0 m/s (200 ft./min.) Lineage Power 36 Vdc to 75 Vdc Input, 12 Vdc Output (continued 0.4 Figure 19. JAW050B1 Power Dissipation vs 0.6 Figure 20. JAW075B1 Power Dissipation vs ...
Page 12
... NO HEAT SINK 1/4 IN. HEAT SINK 1/2 IN. HEAT SINK 1 IN. HEAT SINK 1 1/2 IN. HEAT SINK 0 0.5 1.0 1.5 2.0 (100) (200) (300) (400) AIR VELOCITY, m/s (ft./min.) Curves; Either Orientation = output current 6 ° ° using Figure 20 Lineage Power 2.5 3.0 (500) (600) 8-3233 (F) ...
Page 13
... θ cs Figure 23. Resistance from Case-to-Sink and Sink-to-Ambient Lineage Power 36 Vdc to 75 Vdc Input, 12 Vdc Output For a managed interface using thermal grease or foils, (continued) a value of θcs = 0.1 °C/W to 0.3 °C/W is typical. The solution for heat sink resistance is: (continued) θ ...
Page 14
... DIA SOLDER-PLATED BRASS, 7 PLACES 7.1 STANDOFF, (0.28) 4 PLACES 12.7 (0.50) V (−) V (− 10.16 (0.400) CASE −SEN TRIM ON/OFF +SEN V (+) V (+) I O 48.26 (1.900) 4.8 48.3 (1.90) (0.19) April 2008 2.06 (0.081) DIA SOLDER- PLATED BRASS, 2 PLACES (+)) (V (−) AND MOUNTING INSERTS M3 x 0.5 THROUGH, 4 PLACES 7.1 (0.28) 10.16 17.78 (0.400) (0.700) 25.40 (1.000) 35.56 (1.400) Lineage Power 8-716(F).j ...
Page 15
... I O +SEN ON/OFF TRIM −SEN CASE 10.16 (0.400) V (−) V (− 12.7 (0.50) MODULE OUTLINE Output Remote On/Off Current Logic 50 W 4.2 A Negative 75 W 6.25 A Negative 50 W 4.2 A Positive 75 W 6.25 A Positive 61.0 (2.40) 35.56 (1.400) 25.40 (1.000) 17.78 10.16 (0.700) (0.400) Device Comcode Code JAW050B1 108449398 JAW075B1 TBD JAW050B TBD JAW075B TBD 8-716(F).j 15 ...
Page 16
... Lineage Power reserves the right to make changes to the produc t(s) or information contained herein without notice. No liability is ass umed as a res ult of their use or applic ation. No rights under any patent acc ompany the sale of any oduct information. ...