UPC358HA NEC, UPC358HA Datasheet

no-image

UPC358HA

Manufacturer Part Number
UPC358HA
Description
UPC358HALOW POWER DUAL OPERATIONAL AMPLIFIERS
Manufacturer
NEC
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
UPC358HA
Manufacturer:
NEC
Quantity:
231
Part Number:
UPC358HA
Manufacturer:
NEC
Quantity:
1 000
Part Number:
UPC358HA
Manufacturer:
NEC
Quantity:
1 000
Part Number:
UPC358HA
Manufacturer:
NEC
Quantity:
20 000
Part Number:
UPC358HA
Manufacturer:
NEC
Quantity:
10 449
Document No. G11765EJ4V0DS00 (4th edition)
(Previous No. IC-1284)
Date Published May 1997 N
Printed in Japan
DESCRIPTION
designed to operate from a single power supply over a
wide range of voltages. Operation from split power
supplies is also possible and the power supply current
drain is very low. Further advantage, the input common-
mode voltage range includes ground in the linear mode.
EQUIVALENT CIRCUIT (1/2 Circuit)
ORDERING INFORMATION
I
I
N
I
The PC358 is a dual operational amplifier which is
Q
1
Part Number
Q
Q
PC358C
PC358G2
PC358HA
2
8
Q
Q
6 A
9
3
LOW POWER DUAL OPERATIONAL AMPLIFIERS
Q
4
6 A
C
C
Q
The information in this document is subject to change without notice.
10
Q
8-pin plastic DIP (300 mil)
8-pin plastic SOP (225 mil)
9-pin slim SIP
11
Q
100 A
12
BIPOLAR ANALOG INTEGRATED CIRCUIT
The mark
Q
50 A
7
Q
5
Package
Q
Q
DATA SHEET
6
13
R
SC
V +
V –
OUT
shows major revised points.
FEATURES
• Internally frequency compensation
• Wide output voltage swing V
• Common mode input voltage range includes V
• Wide supply voltage range
• Output short circuit protection
PIN CONFIGURATION (Marking Side)
3 V to 30 V (Single)
1.5 V to 15 V (Split)
OUT
1
I
V
I
N1
I1
1
2
1
2
3
4
PC358C, 358G2
3
PC358HA
1
1
+
4
+
5
+
2
6
+ –
2
7
to V
8
7
6
5
V
OUT
I
I
8
I2
N2
PC358
+
+
–1.5 V
9
2
©
1997

Related parts for UPC358HA

UPC358HA Summary of contents

Page 1

LOW POWER DUAL OPERATIONAL AMPLIFIERS DESCRIPTION The PC358 is a dual operational amplifier which is designed to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the power ...

Page 2

... HA Package Output Short Circuit Duration Operating Ambient Temperature Storage Temperature Notes 1. Reverse connection of supply voltage can cause destruction. 2. The input voltage should be allowed to input without damage or destruction independent of the magnitude + Either input signal should not be allowed to go negative by more than 0.3 V. The normal operation will establish when the both inputs are within the Common Mode Input Voltage Range of electrical characteristics ...

Page 3

TYPICAL PERFORMANCE CHARACTERISTICS (T POWER DISSIPATION 600 500 PC358G2 400 PC358C, 358HA 300 200 100 Operating Ambient Temperature - °C A INPUT OFFSET VOLTAGE ˚ ...

Page 4

OUTPUT SHORT CIRCUIT CURRENT 70 – – Ambient Temperature - ˚C A OPEN LOOP VOLTAGE GAIN 160 120 ...

Page 5

SLEW RATE 0.3 0.2 0.1 ± ± ± – Operating Ambient Temperature - ˚C A OUTPUT SINK CURRENT LIMIT 100 0.5 ...

Page 6

PACKAGE DRAWINGS 8 PIN PLASTIC DIP (300 mil NOTES 1) Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. 2) ltem ...

Page 7

PIN PLASTIC SOP (225 mil NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition. PC358 detail of lead ...

Page 8

PIN PLASTIC SLIM SIP NOTE Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition ...

Page 9

RECOMMENDED SOLDERING CONDITIONS When soldering these products highly recommended to observe the conditions as shown below. If other soldering processes are used the soldering is performed under different conditions, please make sure to consult with our ...

Page 10

... REFERENCE DOCUMENTS QUALITY GRADES ON NEC SEMICONDUCTOR DEVICES SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL IC PACKAGE MANUAL GUIDE TO QUALITY ASSUARANCE FOR SEMICONDUCTOR DEVICES SEMICONDUCTORS SELECTION GUIDE NEC SEMICONDUCTOR DEVICE RELIABILITY/ QUALITY CONTROL SYSTEM - STANDARD LINEAR IC 10 PC358 C11531E C10535E C10943X MEI-1202 X10679E IEI-1212 ...

Page 11

PC358 11 ...

Page 12

... Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...

Related keywords