93C56 STMicroelectronics, 93C56 Datasheet

no-image

93C56

Manufacturer Part Number
93C56
Description
93C562K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM
Manufacturer
STMicroelectronics
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
93C56
Manufacturer:
MTI
Quantity:
248
Part Number:
93C56
Manufacturer:
NSC
Quantity:
5 510
Part Number:
93C56
Manufacturer:
ST
Quantity:
1 000
Part Number:
93C56
Manufacturer:
ST
0
Part Number:
93C56
Manufacturer:
NS/国半
Quantity:
20 000
Part Number:
93C56 3
Manufacturer:
ST
0
Part Number:
93C56 6
Quantity:
2 260
Part Number:
93C56 6
Manufacturer:
ST
0
Part Number:
93C56 6
Manufacturer:
ST
Quantity:
20 000
Part Number:
93C56 @@@@@
Manufacturer:
ST
0
Part Number:
93C56-3G
Manufacturer:
ISSI
Quantity:
20 000
Part Number:
93C56-3GR
Manufacturer:
ISSI
Quantity:
2 070
Part Number:
93C56-3GR
Manufacturer:
ISSI
Quantity:
20 000
FEATURES
• Single supply 5.0V operation
• Low power CMOS technology
• 256 x 8 bit organization (93C56A)
• 128 x 16 bit organization (93C56B)
• Self-timed ERASE and WRITE cycles (including
• Automatic ERAL before WRAL
• Power on/off data protection circuitry
• Industry standard 3-wire serial interface
• Device status signal during ERASE/WRITE
• Sequential READ function
• 100,000 E/W cycles guaranteed
• Data retention > 200 years
• 8-pin PDIP and SOIC packages
• Available for the following temperature ranges:
DESCRIPTION
The Microchip Technology Inc. 93C56A/B is a 2K-bit,
low-voltage serial Electrically Erasable PROM. The
device memory is configured as 256 x 8 bits (93C56A)
or 128 x 16 bits (93C56B). Advanced CMOS technol-
ogy makes this device ideal for low-power, nonvolatile
memory applications. The 93C56A/B is available in
standard 8-pin DIP and surface mount SOIC packages.
This device is only recommeded for 5V automotive
temperature applications. For all commercial and
industrial applications, the 93LC56A/B is recom-
mended.
M
Microwire is a registered trademark of National Semiconductor.
- 1 mA active current (typical)
- 1 A standby current (maximum)
auto-erase)
cycles
- Automotive (E):
1998 Microchip Technology Inc.
2K 5.0V Automotive Temperature Microwire
-40 C to
+125 C
Preliminary
PACKAGE TYPE
BLOCK DIAGRAM
DI
CS
CLK
PDIP
SOIC
GENERATOR
93C56A/B
REGISTER
MEMORY
DECODE
MEMORY
CLK
LOGIC
ARRAY
DO
CLOCK
CS
DATA
CLK
DI
®
DO
CS
DI
Serial EEPROM
1
2
3
4
1
2
3
4
V
CC
COUNTER
ADDRESS
DECODER
ADDRESS
8
7
6
5
8
7
6
5
V
V
NC
NC
V
CC
SS
DS21206B-page 1
SS
V
NC
NC
V
OUTPUT
BUFFER
CC
SS
DO

Related parts for 93C56

93C56 Summary of contents

Page 1

... DESCRIPTION The Microchip Technology Inc. 93C56A 2K-bit, low-voltage serial Electrically Erasable PROM. The device memory is configured as 256 x 8 bits (93C56A) or 128 x 16 bits (93C56B). Advanced CMOS technol- ogy makes this device ideal for low-power, nonvolatile memory applications. The 93C56A/B is available in standard 8-pin DIP and surface mount SOIC packages ...

Page 2

... ELECTRICAL CHARACTERISTICS 1.1 Maximum Ratings* ...................................................................................7. All inputs and outputs w.r.t. ................ -0.6V to Vcc +1. Storage temperature .....................................- +150 C Ambient temp. with power applied.................- +125 C Soldering temperature of leads (10 seconds) ............. +300 C ESD protection on all pins................................................4 kV *Notice: Stresses above those listed under “Maximum ratings” may cause permanent damage to the device ...

Page 3

... RESET status. 2.2 Serial Clock (CLK) The Serial Clock is used to synchronize the communi- cation between a master device and the 93C56A/B. Opcode, address, and data bits are clocked in on the positive edge of CLK. Data bits are also clocked out on the positive edge of CLK. ...

Page 4

... FUNCTIONAL DESCRIPTION Instructions, addresses, and write data are clocked into the DI pin on the rising edge of the clock (CLK). The DO pin is normally held in a HIGH-Z state except when reading data from the device, or when checking the READY/BUSY status during a programming operation. ...

Page 5

... ERAL cycle is com- CSL plete. T CSL ••• CSL 0 X ••• Preliminary 93C56A/B CHECK STATUS BUSY READY HIGH-Z CHECK STATUS BUSY READY HIGH-Z DS21206B-page 5 ...

Page 6

... The READ instruction outputs the serial data of the addressed memory location on the DO pin. A dummy zero bit precedes the 8-bit (93C56A) or 16-bit (93C56B) output string. The output data bits will toggle on the rising edge of the CLK and are stable after the specified time delay (T when CS is held high ...

Page 7

... WRITE The WRITE instruction is followed by 8-bits (93C56A) 16-bits (93C56B) of data which are written into the specified address. After the last data bit is clocked into the DI pin, the self-timed auto-erase and programming cycle begins. The DO pin indicates the READY/BUSY status of the ...

Page 8

... NOTES: DS21206B-page 8 Preliminary 1998 Microchip Technology Inc. ...

Page 9

... NOTES: 1998 Microchip Technology Inc. Preliminary 93C56A/B DS21206B-page 9 ...

Page 10

... NOTES: DS21206B-page 10 Preliminary 1998 Microchip Technology Inc. ...

Page 11

... PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. 93C56A/B /P Package: Temperature Range: Device: Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recom- mended workarounds ...

Page 12

M W ORLDWIDE AMERICAS Corporate Office Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 602-786-7200 Fax: 602-786-7277 Technical Support: 602 786-7627 Web: http://www.microchip.com Atlanta Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: ...

Related keywords