IA82510-PLC28I-01 InnovASIC Inc, IA82510-PLC28I-01 Datasheet
IA82510-PLC28I-01
Available stocks
Related parts for IA82510-PLC28I-01
IA82510-PLC28I-01 Summary of contents
Page 1
... MILES TM also verifies the clone against the original IC so that even the "undocumented features" are duplicated. This data sheet documents all necessary engineering information about the IA82510 including functional and I/O descriptions, electrical characteristics, and applicable timing. IA82510 ...
Page 2
... ASYNCHRONOUS SERIAL CONTROLLER DESCRIPTION The IA82510 is an asynchronous serial controller that provides a CPU interface to one transmit and one receive channel Form, Fit, and Function compatible with the Intel 82510. Configuration registers are used to control the serial channel, interrupts, and modes of operation. ...
Page 3
... Control Character Detection RTS and CTS modes See the Register Description for more details. Bus Interface The Bus Interface is a simple interface that allows a micro-processor or micro-controller to read and write the IA82510 Registers. It consists of the following I/O lines: A0, A1 Bit Address D0- Bit Data ...
Page 4
... RXDATA 000 RXF 001 TCM 110 TMCR 011 TMD 011 TMIE 110 TMST 011 TXDATA 000 TXF 001 Copyright 2001 innovASIC The End of Obsolescence Table 1 – IA82510 Register Summary Bank DLAB ...
Page 5
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER AC/DC Parameters Absolute maximum ratings: Supply Voltage, V …………………………….…-0.3V to +6.0V DD Input Voltage, V …………………………………-0. Input Pin Current, IIN…………………………….±10 mA Operating Temperature Range… ...
Page 6
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER DC Characteristics Symbol Parameter V Input Low Voltage IL V Input High Voltage-Cerdip IH1 V Input High Voltage-LCC IH2 V Output Low Voltage OL V Output High Voltage OH I Input Leakage Current LI I 3-State Leakage Current LO I Power Supply Current CC I Strapping Pullup Resistor ...
Page 7
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER AC Characteristics Parameter Min CLK period 54 ns CLK period 54 ns CLK Low Time 25 ns CLK High Time 25 ns CLK Rise Time CLK Fall Time CLK Rise Time CLK Fall Time Crystal Frequency 1 Mhz Reset Width 8 * Clock Period RTS/DTR Low Setup ...
Page 8
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER Packaging Information PLCC Package PIN 1 IDENTIFIER & ZONE D3 TOP VIEW .81 / .66 e . SIDE VIEW Copyright 2001 innovASIC The End of Obsolescence SEATING PLANE .10 .51 MIN. R 1.14 / .64 ENG211001219-01 Page Data Sheet As of Production Ver BOTTOM VIEW ...
Page 9
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER PDIP Package TOP LEAD 1 IDENTIFIER 1 LEAD COUNT DIRECTION SIDE VIEW (LENGTH) Copyright 2001 innovASIC The End of Obsolescence ENG211001219-01 Page Data Sheet As of Production Ver SIDE VIEW (WIDTH) Lead Count 28 (in Inches) ...
Page 10
... Ordering Information The IA82510 may be ordered per the tables below. Production Version -01 Order Number Environment IA82510-PDW28I-01 Industrial IA82510-PLC28I-01 Industrial OEM Part Number Cross-Reference The following table identifies which OEM Part Number is compatible with the corresponding InnovASIC Part Number innovASIC Part Number IA82510-PLC28I ...
Page 11
... When using the -00 version of the IA82510, please refer to the errata section, "Production Version -00, Errata". Production Version -01, Errata The following errata are known problems with the -01 version of the IA82510. This is inclusive of all package types and environment grades. A workaround to the identified problem has been provided where possible. ALL ERRATA LISTED IN PRODUCTION VERION -00 HAVE BEEN FIXED IN THIS VERSION OF THE DEVICE UNLESS OTHERWISE NOTED ...
Page 12
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER can be altered to the point of confusing the downstream receiver. Workaround: Change firmware to Manual TX mode to control RTS vs. start of character. Copyright 2001 innovASIC The End of Obsolescence ENG211001219-01 Page Data Sheet As of Production Ver. 01 www.innovasic.com Customer Support: 1-888-824-4184 ...
Page 13
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER Production Version -00, Errata The following errata are known problems with the -00 version of the IA82510. This is inclusive of all package types and environment grades. A workaround to the identified problem has been provided where possible. 1. Problem: Scrambled data during boot code shuts down UART, however device works for ...
Page 14
... IA82510 ASYNCHRONOUS SERIAL CONTROLLER 6. Problem: Receiving streamed data has many framing errors at fast baud rates (divisor=6) through bad modem lines. Analysis: DPLL is not robust for RXD signal with more than 1/16 bit time of variation. Workaround: None 7. Problem: Difficulty starting oscillator with crystal. ...