AT90USB162 Atmel Corporation, AT90USB162 Datasheet - Page 13

no-image

AT90USB162

Manufacturer Part Number
AT90USB162
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of AT90USB162

Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
22
Ext Interrupts
21
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
5
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
No
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT90USB162-16AU
Manufacturer:
Atmel
Quantity:
30 024
Part Number:
AT90USB162-16AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT90USB162-16AU
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT90USB162-16AUR
Manufacturer:
Atmel
Quantity:
2 751
Part Number:
AT90USB162-16AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT90USB162-16MU
Manufacturer:
Atmel
Quantity:
42 926
Part Number:
AT90USB162-16MU
Manufacturer:
ATMEL
Quantity:
3 470
Part Number:
AT90USB162-16MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT90USB162-16MUR
Manufacturer:
TT
Quantity:
400 000
4.9
4.9.1
4.9.2
4.10
7618C–AVR–07/08
Erasing the Flash
Starting the Application
Request from Host
Answers from Bootloader
The flow described below allows the user to erase the Flash memory.
The Full Chip erase command erases the whole Flash.
To start the erasing operation, the Host sends a DFU_DNLOAD request with a Write Command
in the data field (2 bytes).
The device has two possible answers to a DFU_GETSTATUS request:
The flow described below allows to start the application directly from the bootloader upon a spe-
cific command reception.
Two options are possible:
To start the application, the Host sends a DFU_DNLOAD request with the specified application
start type in the data field (3 or 5 bytes).
This request is immediately followed by a second DFU_DNLOAD request with no data field to
start the application with one of the 2 options.
Command Identifier
• If the chip is protected from program access, an “err_WRITE” status is returned to the Host.
• Otherwise, the device status is “OK“.
Id_write_command
Start the application with an internal hardware reset using watchdog.
When the device receives this command the watchdog is enabled and the bootloader enters
a waiting loop until the watchdog resets the device.
Start the application without reset.
A jump at the address 0000h is used to start the application without reset.
04h
data[0]
00h
SETUP
IN
OUT
data[1]
FFh
data[2]
Byte value (1 byte)
DFU_UPLOAD
ZLP
data[3]
data[4]
Full chip Erase (bits at FFh)
Description
13

Related parts for AT90USB162