ATmega1284PR231 Atmel Corporation, ATmega1284PR231 Datasheet - Page 59
ATmega1284PR231
Manufacturer Part Number
ATmega1284PR231
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT86RF231.pdf
(198 pages)
2.ATMEGA1284PR231.pdf
(380 pages)
3.ATMEGA1284PR231.pdf
(20 pages)
Specifications of ATmega1284PR231
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
- Current page: 59 of 198
- Download datasheet (5Mb)
8111C–MCU Wireless–09/09
Table 7-10.
There are two different options for handling reserved frame types.
Short Acknowledgment Frame (ACK) Start Timing
Register bit AACK_ACK_TIME (register 0x17, XAH_CTRL_1), see
defines the symbol time between frame reception and transmission of an acknowledgment
frame.
1.
2.
3.
0x2E
0x2E
0x2E
AACK_UPLD_RES_FT = 1, AACK_FLT_RES_FT = 0:
Any non-corrupted frame with a reserved frame type is indicated by an
IRQ_3 (TRX_END) interrupt. No further address filtering is applied on those frames. An
IRQ_5 (AMI) interrupt is never generated and the acknowledgment subfield is ignored.
AACK_UPLD_RES_FT = 1, AACK_FLT_RES_FT = 1:
If AACK_FLT_RES_FT = 1 any frame with a reserved frame type is filtered by the
address filter similar to a data frame as described in the standard. This implies the
generation of the IRQ_5 (AMI) interrupts upon address match. An IRQ_3 (TRX_END)
interrupt is only generated if the address matched and the frame was not corrupted. An
acknowledgment is only send, when the ACK request subfield was set in the received
frame and an IRQ_3 (TRX_END) interrupt occurred.
AACK_UPLD_RES_FT = 0:
Any received frame indicated as a reserved frame is discarded.
RX_AACK Configuration to Receive Reserved Frame Types (Continued)
7:6
3
4
AACK_I_AM_COORD
AACK_DIS_ACK
AACK_FVN_MODE
0: device is not PAN coordinator
1: device is PAN coordinator
0: Enable generation of acknowledgment
1: Disable generation of acknowledgment
Controls the ACK behavior, depending on FCF
frame version number
0x00: acknowledges only frames with version
number 0, i.e. according to IEEE 802.15.4-2003
frames
0x01: acknowledges only frames with version
number 0 or 1, i.e. frames according to
IEEE 802.15.4-2006
0x10: acknowledges only frames with version
number 0 or 1 or 2
0x11: acknowledges all frames, independent of
the FCF frame version number
Table 7-11 on page
AT86RF231
60,
59
Related parts for ATmega1284PR231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika