ATmega1284RZAP Atmel Corporation, ATmega1284RZAP Datasheet - Page 103

no-image

ATmega1284RZAP

Manufacturer Part Number
ATmega1284RZAP
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega1284RZAP

Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
No
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
0.25
Antenna Diversity
No
External Pa Control
No
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
16.0
Transmit Current Consumption (ma)
17.0
Link Budget (dbm)
104
13.9
13.9.1
8059D–AVR–11/09
Register Description
TCCR0A – Timer/Counter Control Register A
• Bits 7:6 – COM0A1:0: Compare Match Output A Mode
These bits control the Output Compare pin (OC0A) behavior. If one or both of the COM0A1:0
bits are set, the OC0A output overrides the normal port functionality of the I/O pin it is connected
to. However, note that the Data Direction Register (DDR) bit corresponding to the OC0A pin
must be set in order to enable the output driver.
When OC0A is connected to the pin, the function of the COM0A1:0 bits depends on the
WGM02:0 bit setting.
are set to a normal or CTC mode (non-PWM).
Table 13-2.
Table 13-3
mode.
Table 13-3.
Note:
Table 13-4 on page 104
to phase correct PWM mode.
Bit
0x24 (0x44)
Read/Write
Initial Value
COM0A1
COM0A1
0
0
1
1
0
0
1
1
1. A special case occurs when OCR0A equals TOP and COM0A1 is set. In this case, the Com-
pare Match is ignored, but the set or clear is done at BOTTOM. See
page 98
shows the COM0A1:0 bit functionality when the WGM01:0 bits are set to fast PWM
Compare Output Mode, non-PWM Mode
Compare Output Mode, Fast PWM Mode
COM0A1
R/W
COM0A0
COM0A0
7
0
for more details.
0
1
0
1
0
1
0
1
Table 13-2
COM0A0
shows the COM0A1:0 bit functionality when the WGM02:0 bits are set
R/W
6
0
Description
Normal port operation, OC0A disconnected.
Toggle OC0A on Compare Match
Clear OC0A on Compare Match
Set OC0A on Compare Match
Description
Normal port operation, OC0A disconnected.
WGM02 = 0: Normal Port Operation, OC0A Disconnected.
WGM02 = 1: Toggle OC0A on Compare Match.
Clear OC0A on Compare Match, set OC0A at BOTTOM,
(non-inverting mode).
Set OC0A on Compare Match, clear OC0A at BOTTOM,
(inverting mode).
shows the COM0A1:0 bit functionality when the WGM02:0 bits
COM0B1
R/W
5
0
COM0B0
R/W
4
0
R
3
0
(1)
R
2
0
ATmega1284P
WGM01
R/W
1
0
”Fast PWM Mode” on
WGM00
R/W
0
0
TCCR0A
103

Related parts for ATmega1284RZAP