ATmega1284RZAP Atmel Corporation, ATmega1284RZAP Datasheet - Page 108

• Manufacturer Part Number: ATmega1284RZAP
• Manufacturer: Atmel Corporation

Specifications of ATmega1284RZAP

• Flash (kbytes): 128 Kbytes
• Max. Operating Frequency: 20 MHz
• Max I/o Pins: 32
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Crypto Engine: No
• Sram (kbytes): 16
• Eeprom (bytes): 4096
• Operating Voltage (vcc): 1.8 to 3.6
• Timers: 3
• Frequency Band: 2.4 GHz
• Max Data Rate (mb/s): 0.25
• Antenna Diversity: No
• External Pa Control: No
• Power Output (dbm): 3
• Receiver Sensitivity (dbm): -101
• Receive Current Consumption (ma): 16.0
• Transmit Current Consumption (ma): 17.0
• Link Budget (dbm): 104

13.9.5
13.9.6
13.9.7
8059D–AVR–11/09
OCR0B – Output Compare Register B
TIMSK0 – Timer/Counter Interrupt Mask Register
TIFR0 – Timer/Counter 0 Interrupt Flag Register
The Output Compare Register B contains an 8-bit value that is continuously compared with the
counter value (TCNT0). A match can be used to generate an Output Compare interrupt, or to
generate a waveform output on the OC0B pin.
• Bits 7:3 – Res: Reserved Bits
These bits are reserved bits and will always read as zero.
• Bit 2 – OCIE0B: Timer/Counter Output Compare Match B Interrupt Enable
When the OCIE0B bit is written to one, and the I-bit in the Status Register is set, the
Timer/Counter Compare Match B interrupt is enabled. The corresponding interrupt is executed if
a Compare Match in Timer/Counter occurs, i.e., when the OCF0B bit is set in the Timer/Counter
Interrupt Flag Register – TIFR0.
• Bit 1 – OCIE0A: Timer/Counter0 Output Compare Match A Interrupt Enable
When the OCIE0A bit is written to one, and the I-bit in the Status Register is set, the
Timer/Counter0 Compare Match A interrupt is enabled. The corresponding interrupt is executed
if a Compare Match in Timer/Counter0 occurs, i.e., when the OCF0A bit is set in the
Timer/Counter 0 Interrupt Flag Register – TIFR0.
• Bit 0 – TOIE0: Timer/Counter0 Overflow Interrupt Enable
When the TOIE0 bit is written to one, and the I-bit in the Status Register is set, the
Timer/Counter0 Overflow interrupt is enabled. The corresponding interrupt is executed if an
overflow in Timer/Counter0 occurs, i.e., when the TOV0 bit is set in the Timer/Counter 0 Inter-
rupt Flag Register – TIFR0.
• Bits 7:3 – Res: Reserved Bits
These bits are reserved bits in the ATmega1284P and will always read as zero.
Bit
0x28 (0x48)
Read/Write
Initial Value
Bit
(0x6E)
Read/Write
Initial Value
Bit
0x15 (0x35)
Read/Write
Initial Value
R/W
7
–
R
0
7
0
7
–
R
0
R/W
R
6
–
0
6
0
6
–
R
0
R/W
R
5
–
0
5
0
R
5
–
0
R/W
R
4
–
0
4
0
R
4
–
0
OCR0B[7:0]
R/W
R
3
–
0
3
0
R
3
–
0
OCIE0B
OCF0B
R/W
R/W
R/W
2
0
2
0
2
0
ATmega1284P
OCIE0A
OCF0A
R/W
R/W
R/W
1
0
1
0
1
0
TOIE0
TOV0
R/W
R/W
R/W
0
0
0
0
0
0
TIMSK0
OCR0B
TIFR0
108