ATmega1284RZAP Atmel Corporation, ATmega1284RZAP Datasheet - Page 234

• Manufacturer Part Number: ATmega1284RZAP
• Manufacturer: Atmel Corporation

Specifications of ATmega1284RZAP

• Flash (kbytes): 128 Kbytes
• Max. Operating Frequency: 20 MHz
• Max I/o Pins: 32
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Crypto Engine: No
• Sram (kbytes): 16
• Eeprom (bytes): 4096
• Operating Voltage (vcc): 1.8 to 3.6
• Timers: 3
• Frequency Band: 2.4 GHz
• Max Data Rate (mb/s): 0.25
• Antenna Diversity: No
• External Pa Control: No
• Power Output (dbm): 3
• Receiver Sensitivity (dbm): -101
• Receive Current Consumption (ma): 16.0
• Transmit Current Consumption (ma): 17.0
• Link Budget (dbm): 104

19.9.3
19.9.4
8059D–AVR–11/09
TWSR – TWI Status Register
TWDR – TWI Data Register
• Bit 0 – TWIE: TWI Interrupt Enable
When this bit is written to one, and the I-bit in SREG is set, the TWI interrupt request will be acti-
vated for as long as the TWINT Flag is high.
• Bits 7:3 – TWS: TWI Status
These 5 bits reflect the status of the TWI logic and the 2-wire Serial Bus. The different status
codes are described later in this section. Note that the value read from TWSR contains both the
5-bit status value and the 2-bit prescaler value. The application designer should mask the pres-
caler bits to zero when checking the Status bits. This makes status checking independent of
prescaler setting. This approach is used in this datasheet, unless otherwise noted.
• Bit 2 – Res: Reserved Bit
This bit is reserved and will always read as zero.
• Bits 1:0 – TWPS: TWI Prescaler Bits
These bits can be read and written, and control the bit rate prescaler.
Table 19-7.
To calculate bit rates, see
used in the equation.
In Transmit mode, TWDR contains the next byte to be transmitted. In Receive mode, the TWDR
contains the last byte received. It is writable while the TWI is not in the process of shifting a byte.
This occurs when the TWI Interrupt Flag (TWINT) is set by hardware. Note that the Data Regis-
ter cannot be initialized by the user before the first interrupt occurs. The data in TWDR remains
stable as long as TWINT is set. While data is shifted out, data on the bus is simultaneously
shifted in. TWDR always contains the last byte present on the bus, except after a wake up from
a sleep mode by the TWI interrupt. In this case, the contents of TWDR is undefined. In the case
Bit
(0xB9)
Read/Write
Initial Value
Bit
(0xBB)
Read/Write
Initial Value
TWPS1
0
0
1
1
TWI Bit Rate Prescaler
TWS7
TWD7
R/W
R
7
1
7
1
TWS6
TWD6
R/W
R
TWPS0
0
1
0
1
6
1
6
1
”Bit Rate Generator Unit” on page
TWS5
TWD5
R/W
R
5
1
5
1
TWS4
TWD4
R/W
R
4
1
4
1
Prescaler Value
1
4
16
64
TWD3
TWS3
R/W
R
3
1
3
1
TWD2
R/W
R
2
–
0
2
1
213. The value of TWPS1..0 is
ATmega1284P
TWPS1
TWD1
R/W
R/W
1
0
1
1
TWPS0
TWD0
R/W
R/W
0
0
0
1
TWSR
TWDR
234