ATmega1284RZAP Atmel Corporation, ATmega1284RZAP Datasheet - Page 30

• Manufacturer Part Number: ATmega1284RZAP
• Manufacturer: Atmel Corporation

Specifications of ATmega1284RZAP

• Flash (kbytes): 128 Kbytes
• Max. Operating Frequency: 20 MHz
• Max I/o Pins: 32
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Crypto Engine: No
• Sram (kbytes): 16
• Eeprom (bytes): 4096
• Operating Voltage (vcc): 1.8 to 3.6
• Timers: 3
• Frequency Band: 2.4 GHz
• Max Data Rate (mb/s): 0.25
• Antenna Diversity: No
• External Pa Control: No
• Power Output (dbm): 3
• Receiver Sensitivity (dbm): -101
• Receive Current Consumption (ma): 16.0
• Transmit Current Consumption (ma): 17.0
• Link Budget (dbm): 104

7.3
8059D–AVR–11/09
Low Power Crystal Oscillator
This Crystal Oscillator is a low power oscillator, with reduced voltage swing on the XTAL2 out-
put. It gives the lowest power consumption, but is not capable of driving other clock inputs, and
may be more susceptible to noise in noisy environments. In these cases, refer to the
Crystal Oscillator” on page
Some initial guidelines for choosing capacitors for use with crystals are given in
crystal should be connected as described in
The Low Power Oscillator can operate in three different modes, each optimized for a specific fre-
quency range. The operating mode is selected by the fuses CKSEL3..1 as shown in
Table 7-3.
Notes:
The CKSEL0 Fuse together with the SUT1..0 Fuses select the start-up times as shown in
7-4.
Table 7-4.
Oscillator Source /
Power Conditions
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Frequency Range
1. The frequency ranges are preliminary values. Actual values are TBD.
2. This option should not be used with crystals, only with ceramic resonators.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
Fuse can be programmed in order to divide the internal frequency by 8. It must be ensured
that the resulting divided clock meets the frequency specification of the device.
8.0 - 16.0
0.4 - 0.9
0.9 - 3.0
3.0 - 8.0
Low Power Crystal Oscillator Operating Modes
Start-up Times for the Low Power Crystal Oscillator Clock Selection
(1)
(MHz)
31.
Start-up Time from
Power-down and
Power-save
258 CK
258 CK
1K CK
1K CK
1K CK
CKSEL3..1
100
101
110
111
”Clock Source Connections” on page
(2)
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
Recommended Range for Capacitors C1
14CK + 65 ms
14CK + 65 ms
(V
from Reset
CC
14CK
= 5.0V)
(3)
(2)
(1)
(2)
(1)
(2)
and C2 (pF)
ATmega1284P
12 - 22
12 - 22
12 - 22
–
CKSEL0
CC
0
0
0
0
1
), the CKDIV8
Table
29.
Table
”Full Swing
SUT1..0
7-3. The
00
01
10
11
00
Table
7-3.
30