ATmega1284RZAP Atmel Corporation, ATmega1284RZAP Datasheet - Page 324

no-image

ATmega1284RZAP

Manufacturer Part Number
ATmega1284RZAP
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega1284RZAP

Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
No
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
0.25
Antenna Diversity
No
External Pa Control
No
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
16.0
Transmit Current Consumption (ma)
17.0
Link Budget (dbm)
104
T
Notes:
8059D–AVR–11/09
A
Symbol
t
I
ACID
CC
= -40°C to 85°C, V
1. All DC Characteristics contained in this datasheet are based on simulation and characterization of other AVR microcon-
2. "Max" means the highest value where the pin is guaranteed to be read as low
3. "Min" means the lowest value where the pin is guaranteed to be read as high
4. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady state
5. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
6. All bits set in the
7. Typical values at 25°C. Maximum values are characterized values and not test limits in production
trollers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon.
conditions (non-transient), the following must be observed:
1.)The sum of all IOL, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2.)The sum of all IOL, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3.)The sum of all IOL, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4.)The sum of all IOL, for ports F0-F7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
1)The sum of all IOH, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2)The sum of all IOH, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3)The sum of all IOH, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4)The sum of all IOH, for ports F0-F7 should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Analog Comparator
Propagation Delay
Power Supply Current
Power-save mode
Power-down mode
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
”PRR0 – Power Reduction Register 0” on page
(7)
(7)
(6)
V
WDT disabled, V
Condition
V
Active 1 MHz, V
Active 4 MHz, V
Active 8 MHz, V
Idle 1 MHz, V
Idle 4 MHz, V
Idle 8 MHz, V
32 kHz TOSC enabled,
V
32 kHz TOSC enabled,
V
WDT enabled, V
CC
CC
CC
CC
= 1.8V
= 3V
= 2.7V
= 4.0V
CC
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V)
CC
= 2V
= 3V
= 5V
= 3V
= 3V
Min.
46.
(1)
Typ.
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
750
500
ATmega1284P
Max.
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
(1)
Units
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
ns
324

Related parts for ATmega1284RZAP