ATmega1284RZAP Atmel Corporation, ATmega1284RZAP Datasheet - Page 68

no-image

ATmega1284RZAP

Manufacturer Part Number
ATmega1284RZAP
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega1284RZAP

Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
No
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
0.25
Antenna Diversity
No
External Pa Control
No
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
16.0
Transmit Current Consumption (ma)
17.0
Link Budget (dbm)
104
11.2.6
11.2.7
11.2.8
8059D–AVR–11/09
PCMSK3 – Pin Change Mask Register 3
PCMSK2 – Pin Change Mask Register 2
PCMSK1 – Pin Change Mask Register 1
• Bit 1 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT15..8 pin triggers an interrupt request, PCIF1 becomes set
(one). If the I-bit in SREG and the PCIE1 bit in EIMSK are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 0 – PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF0 becomes set
(one). If the I-bit in SREG and the PCIE0 bit in EIMSK are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 7:0 – PCINT31:24: Pin Change Enable Mask 31:24
Each PCINT31:24-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT31:24 is set and the PCIE2 bit in PCICR is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT31..24 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
• Bit 7:0 – PCINT23:16: Pin Change Enable Mask 23..16
Each PCINT23:16-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT23:16 is set and the PCIE2 bit in PCICR is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT23..16 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
• Bit 7:0 – PCINT15:8: Pin Change Enable Mask 15..8
Each PCINT15:8-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT15:8 is set and the PCIE1 bit in EIMSK is set, pin change interrupt is enabled on the
corresponding I/O pin. If PCINT15:8 is cleared, pin change interrupt on the corresponding I/O
pin is disabled.
Bit
(0x73)
Read/Write
Initial Value
Bit
(0x6D)
Read/Write
Initial Value
Bit
(0x6C)
Read/Write
Initial Value
PCINT31
PCINT23
PCINT15
R/W
R/W
R/W
7
0
7
0
7
0
PCINT30
PCINT22
PCINT14
R/W
R/W
R/W
6
0
6
0
6
0
PCINT29
PCINT21
PCINT13
R/W
R/W
R/W
5
0
5
0
5
0
PCINT28
PCINT20
PCINT12
R/W
R/W
R/W
4
0
4
0
4
0
PCINT27
PCINT19
PCINT11
R/W
R/W
R/W
3
0
3
0
3
0
PCINT26
PCINT18
PCINT10
R/W
R/W
R/W
2
0
2
0
2
0
ATmega1284P
PCINT25
PCINT17
PCINT9
R/W
R/W
R/W
1
0
1
0
1
0
PCINT24
PCINT16
PCINT8
R/W
R/W
R/W
0
0
0
0
0
0
PCMSK2
PCMSK2
PCMSK1
68

Related parts for ATmega1284RZAP