ATmega165P Atmel Corporation, ATmega165P Datasheet - Page 179

• Manufacturer Part Number: ATmega165P
• Manufacturer: Atmel Corporation

Specifications of ATmega165P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

18.10 Examples of Baud Rate Setting
Table 18-4.
1.
8019K–AVR–11/10
Baud
Rate
(bps)
2400
4800
9600
14.4k
19.2k
28.8k
38.4k
57.6k
76.8k
115.2k
230.4k
250k
Max.
(1)
UBRR = 0, Error = 0.0%
UBRR
25
12
6
3
2
1
1
0
–
–
–
–
62.5 Kbps
U2Xn = 0
Examples of UBRR Settings for Commonly Used Oscillator Frequencies
f
Error
-18.6%
osc
-7.0%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
–
–
–
–
= 1.0000 MHz
5. When the last data frame is received by the addressed MCU, the addressed MCU sets
Using any of the 5-bit to 8-bit character frame formats is possible, but impractical since the
Receiver must change between using n and n+1 character frame formats. This makes full-
duplex operation difficult since the Transmitter and Receiver uses the same character size set-
ting. If 5-bit to 8-bit character frames are used, the Transmitter must be set to use two stop bit
(USBSn = 1) since the first stop bit is used for indicating the frame type.
Do not use Read-Modify-Write instructions (SBI and CBI) to set or clear the MPCMn bit. The
MPCMn bit shares the same I/O location as the TXCn Flag and this might accidentally be
cleared when using SBI or CBI instructions.
For standard crystal and resonator frequencies, the most commonly used baud rates for asyn-
chronous operation can be generated by using the UBRR settings in
which yield an actual baud rate differing less than 0.5% from the target baud rate, are bold in the
table. Higher error ratings are acceptable, but the Receiver will have less noise resistance when
the error ratings are high, especially for large serial frames (see
Range” on page
UBRR
the MPCMn bit and waits for a new address frame from master. The process then
repeats from 2.
51
25
12
8
6
3
2
1
1
0
–
–
U2Xn = 1
125 Kbps
Error
-18.6%
-3.5%
-7.0%
0.2%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
–
–
176). The error values are calculated using the following equation:
UBRR
47
23
11
7
5
3
2
1
0
–
–
1
115.2 Kbps
U2Xn = 0
Error[%]
f
Error
-25.0%
osc
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
–
–
= 1.8432 MHz
=
⎛
⎝
BaudRate
------------------------------------------------------- - 1
UBRR
95
47
23
15
11
BaudRate
7
5
3
2
1
0
–
230.4 Kbps
U2Xn = 1
Closest Match
Error
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
–
–
UBRR
⎞
⎠
51
25
12
•
8
6
3
2
1
1
0
–
–
U2Xn = 0
125 Kbps
100%
“Asynchronous Operational
f
Error
-18.6%
osc
-3.5%
-7.0%
Table
0.2%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
ATmega165P
–
–
= 2.0000 MHz
18-4. UBRR values
UBRR
103
51
25
16
12
8
6
3
2
1
–
0
U2Xn = 1
250 Kbps
Error
-3.5%
-7.0%
0.2%
0.2%
0.2%
2.1%
0.2%
8.5%
8.5%
8.5%
0.0%
–
179