ATmega165P Atmel Corporation, ATmega165P Datasheet - Page 196

no-image

ATmega165P

Manufacturer Part Number
ATmega165P
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega165P

Flash (kbytes)
16 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
54
Ext Interrupts
17
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega165P-16AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega165P-16ANR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega165P-16AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega165P-16AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega165PA-AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega165PV-8AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
19.5
19.5.1
19.5.2
8019K–AVR–11/10
Register Descriptions
USIDR – USI Data Register
USISR – USI Status Register
The USI uses no buffering of the Serial Register, that is, when accessing the Data Register
(USIDR) the Serial Register is accessed directly. If a serial clock occurs at the same cycle the
register is written, the register will contain the value written and no shift is performed. A (left) shift
operation is performed depending of the USICS1..0 bits setting. The shift operation can be con-
trolled by an external clock edge, by a Timer/Counter0 Compare Match, or directly by software
using the USICLK strobe bit. Note that even when no wire mode is selected (USIWM1..0 = 0)
both the external data input (DI/SDA) and the external clock input (USCK/SCL) can still be used
by the Shift Register.
The output pin in use, DO or SDA depending on the wire mode, is connected via the output latch
to the most significant bit (bit 7) of the Data Register. The output latch is open (transparent) dur-
ing the first half of a serial clock cycle when an external clock source is selected (USICS1 = 1),
and constantly open when an internal clock source is used (USICS1 = 0). The output will be
changed immediately when a new MSB written as long as the latch is open. The latch ensures
that data input is sampled and data output is changed on opposite clock edges.
Note that the corresponding Data Direction Register to the pin must be set to one for enabling
data output from the Shift Register.
The Status Register contains Interrupt Flags, line Status Flags and the counter value.
• Bit 7 – USISIF: Start Condition Interrupt Flag
When Two-wire mode is selected, the USISIF Flag is set (to one) when a start condition is
detected. When output disable mode or Three-wire mode is selected and (USICSx = 0b11 &
USICLK = 0) or (USICS = 0b10 & USICLK = 0), any edge on the SCK pin sets the flag.
An interrupt will be generated when the flag is set while the USISIE bit in USICR and the Global
Interrupt Enable Flag are set. The flag will only be cleared by writing a logical one to the USISIF
bit. Clearing this bit will release the start detection hold of USCL in Two-wire mode.
A start condition interrupt will wakeup the processor from all sleep modes.
• Bit 6 – USIOIF: Counter Overflow Interrupt Flag
This flag is set (one) when the 4-bit counter overflows (that is, at the transition from 15 to 0). An
interrupt will be generated when the flag is set while the USIOIE bit in USICR and the Global
Interrupt Enable Flag are set. The flag will only be cleared if a one is written to the USIOIF bit.
Clearing this bit will release the counter overflow hold of SCL in Two-wire mode.
A counter overflow interrupt will wakeup the processor from Idle sleep mode.
Bit
(0xBA)
Read/Write
Initial Value
Bit
(0xB9)
Read/Write
Initial Value
USISIF
R/W
MSB
7
0
R/W
7
0
USIOIF
R/W
6
0
R/W
6
0
USIPF
R/W
5
0
R/W
5
0
USIDC
R
4
0
R/W
4
0
USICNT3
R/W
3
0
R/W
3
0
USICNT2
R/W
2
0
R/W
2
0
USICNT1
ATmega165P
R/W
R/W
1
0
1
0
USICNT0
LSB
R/W
R/W
0
0
0
0
USIDR
USISR
196

Related parts for ATmega165P