ATmega3290 Atmel Corporation, ATmega3290 Datasheet - Page 6

• Manufacturer Part Number: ATmega3290
• Manufacturer: Atmel Corporation

Specifications of ATmega3290

• Flash (kbytes): 32 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

2.2
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2552KS–AVR–04/11
Comparison between ATmega329, ATmega3290, ATmega649 and ATmega6490
Pin Descriptions
V
GND
Port A (PA7..PA0)
Port B (PB7..PB0)
CC
The ATmega329, ATmega3290, ATmega649, and ATmega6490 differs only in memory sizes,
pin count and pinout.
devices.
Table 2-1.
The following section describes the I/O-pin special functions.
Digital supply voltage.
Ground.
Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port A output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port A pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port A also serves the functions of various special features of the ATmega329/3290/649/6490
as listed on
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port B output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port B has better driving capabilities than the other ports.
Port B also serves the functions of various special features of the ATmega329/3290/649/6490
as listed on
Device
ATmega329
ATmega3290
ATmega649
ATmega6490
page
page
Configuration Summary
Flash
32Kbytes
32Kbytes
64Kbytes
64Kbytes
67.
68.
Table 2-1 on page 6
EEPROM
1Kbytes
1K bytes
2Kbytes
2Kbytes
RAM
2Kbytes
2Kbytes
4Kbytes
4Kbytes
summarizes the different configurations for the four
ATmega329/3290/649/6490
LCD
Segments
4 x 25
4 x 40
4 x 25
4 x 40
General Purpose
I/O Pins
54
69
54
69
6