ATmega3290P Atmel Corporation, ATmega3290P Datasheet - Page 211

• Manufacturer Part Number: ATmega3290P
• Manufacturer: Atmel Corporation

Specifications of ATmega3290P

• Flash (kbytes): 32 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.3
21.3.1
21.3.2
8021G–AVR–03/11
Register Description
ADCSRB – ADC Control and Status Register B
ACSR – Analog Comparator Control and Status Register
Table 21-1.
• Bit 6 – ACME: Analog Comparator Multiplexer Enable
When this bit is written logic one and the ADC is switched off (ADEN in ADCSRA is zero), the
ADC multiplexer selects the negative input to the Analog Comparator. When this bit is written
logic zero, AIN1 is applied to the negative input of the Analog Comparator. For a detailed
description of this bit, see
• Bit 7 – ACD: Analog Comparator Disable
When this bit is written logic one, the power to the Analog Comparator is switched off. This bit
can be set at any time to turn off the Analog Comparator. This will reduce power consumption in
Active and Idle mode. When changing the ACD bit, the Analog Comparator Interrupt must be
disabled by clearing the ACIE bit in ACSR. Otherwise an interrupt can occur when the bit is
changed.
• Bit 6 – ACBG: Analog Comparator Bandgap Select
When this bit is set, a fixed bandgap reference voltage replaces the positive input to the Analog
Comparator. When this bit is cleared, AIN0 is applied to the positive input of the Analog Compar-
ator. When the bandgap reference is used as input to the analog comparator, it will take a
certain time for the voltage to stabilize. If not stabilized, the first conversion may give a wrong
value. See
• Bit 5 – ACO: Analog Comparator Output
The output of the Analog Comparator is synchronized and then directly connected to ACO. The
synchronization introduces a delay of 1 - 2 clock cycles.
Bit
(0x7B)
Read/Write
Initial Value
Bit
0x30 (0x50)
Read/Write
Initial Value
ACME
1
1
1
1
1
1
1
”Internal Voltage Reference” on page 48
Analog Comparator Multiplexed Input (Continued)
ACD
R/W
ADEN
7
0
R
7
–
0
0
0
0
0
0
0
0
ACBG
ACME
R/W
R/W
”Analog Comparator Multiplexed Input” on page
6
0
6
0
MUX2..0
001
010
011
100
101
110
111
ACO
N/A
R
5
R
5
–
0
Analog Comparator Negative Input
ADC1
ADC2
ADC3
ADC4
ADC5
ADC6
ADC7
R/W
ACI
4
0
R
4
–
0
ACIE
R/W
3
0
3
–
R
0
ATmega329P/3290P
ADTS2
ACIC
R/W
R/W
2
0
2
0
ADTS1
ACIS1
R/W
R/W
1
0
1
0
210.
ADTS0
ACIS0
R/W
R/W
0
0
0
0
ADCSRB
ACSR
211