ATmega3290P Atmel Corporation, ATmega3290P Datasheet - Page 238

• Manufacturer Part Number: ATmega3290P
• Manufacturer: Atmel Corporation

Specifications of ATmega3290P

• Flash (kbytes): 32 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8021G–AVR–03/11
Note:
Before a re-initialization is done, the LCD controller/driver should be disabled
Assembly Code Example
C Code Example
LCD_Init:
Void LCD_Init(void);
{
LCDCRB = (1<<LCDCS) | (1<<LCDMUX1)| (1<<LCDPM2);
}
; Use 32kHz crystal oscillator
; 1/3 Bias and 1/3 duty, SEG21:SEG24 is used as port pins
ldi
sts
; Using 16 as prescaler selection and 7 as LCD Clock Divide
; gives a frame rate of 49 Hz
ldi
sts
; Set segment drive time to 125 µs and output voltage to 3.3 V
ldi
sts
; Enable LCD, default waveform and no interrupt enabled
ldi
sts
ret
/* Use 32kHz crystal oscillator */
/* 1/3 Bias and 1/3 duty, SEG21:SEG24 is used as port pins */
/* Using 16 as prescaler selection and 7 as LCD Clock Divide */
/* gives a frame rate of 49 Hz */
LCDFRR = (1<<LCDCD2) | (1<<LCDCD1);
/* Set segment drive time to 125 µs and output voltage to 3.3 V*/
LCDCCR = (1<<LCDDC1) | (1<<LCDCC3) | (1<<LCDCC2) | (1<<LCDCC1);
/* Enable LCD, default waveform and no interrupt enabled */
LCDCRA = (1<<LCDEN);
1. See
r16, (1<<LCDCS) | (1<<LCDMUX1)| (1<<LCDPM2)
LCDCRB, r16
r16, (1<<LCDCD2) | (1<<LCDCD1)
LCDFRR, r16
r16, (1<<LCDDC1) | (1<<LCDCC3) | (1<<LCDCC2) | (1<<LCDCC1)
LCDCCR, r16
r16, (1<<LCDEN)
LCDCRA, r16
”About Code Examples” on page 9
(1)
(1)
ATmega329P/3290P
238