ATmega3290P Atmel Corporation, ATmega3290P Datasheet - Page 324

• Manufacturer Part Number: ATmega3290P
• Manufacturer: Atmel Corporation

Specifications of ATmega3290P

• Flash (kbytes): 32 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Table 27-19. JTAG Programming Instruction Set (Continued)
Notes:
8021G–AVR–03/11
Instruction
8f. Read Fuses and Lock Bits
9a. Enter Signature Byte Read
9b. Load Address Byte
9c. Read Signature Byte
10a. Enter Calibration Byte Read
10b. Load Address Byte
10c. Read Calibration Byte
11a. Load No Operation Command
1. This command sequence is not required if the seven MSB are correctly set by the previous command sequence (which is
2. Repeat until o = “1”.
3. Set bits to “0” to program the corresponding Fuse, “1” to unprogram the Fuse.
4. Set bits to “0” to program the corresponding Lock bit, “1” to leave the Lock bit unchanged.
5. “0” = programmed, “1” = unprogrammed.
6. The bit mapping for Fuses Extended byte is listed in
7. The bit mapping for Fuses High byte is listed in
8. The bit mapping for Fuses Low byte is listed in
9. The bit mapping for Lock bits byte is listed in
10. Address bits exceeding PCMSB and EEAMSB
11. All TDI and TDO sequences are represented by binary digits (0b...).
normally the case).
a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = don’t care
TDI Sequence
0111010_00000000
0111110_00000000
0110010_00000000
0110110_00000000
0110111_00000000
0000011_bbbbbbbb
0110010_00000000
0110011_00000000
0000011_bbbbbbbb
0110110_00000000
0110111_00000000
0100011_00000000
0110011_00000000
0100011_00001000
0100011_00001000
Table 27-1 on page 296
Table 27-5 on page 298
(Table 27-13
Table 27-4 on page 298
Table 27-3 on page 297
and
Table
27-14) are don’t care
TDO Sequence
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
ATmega329P/3290P
Notes
(5)
Fuse Ext. byte
Fuse High byte
Fuse Low byte
Lock bits
324