ATmega329P Atmel Corporation, ATmega329P Datasheet - Page 157

• Manufacturer Part Number: ATmega329P
• Manufacturer: Atmel Corporation

Specifications of ATmega329P

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

17.10.2
17.10.3
17.10.4
8021G–AVR–03/11
TCNT2 – Timer/Counter Register
OCR2A – Output Compare Register A
ASSR – Asynchronous Status Register
Table 17-6.
The Timer/Counter Register gives direct access, both for read and write operations, to the
Timer/Counter unit 8-bit counter. Writing to the TCNT2 Register blocks (removes) the compare
match on the following timer clock. Modifying the counter (TCNT2) while the counter is running,
introduces a risk of missing a compare match between TCNT2 and the OCR2A Register.
The Output Compare Register A contains an 8-bit value that is continuously compared with the
counter value (TCNT2). A match can be used to generate an Output Compare interrupt, or to
generate a waveform output on the OC2A pin.
• Bit 4 – EXCLK: Enable External Clock Input
When EXCLK is written to one, and asynchronous clock is selected, the external clock input buf-
fer is enabled and an external clock can be input on Timer Oscillator 1 (TOSC1) pin instead of a
32kHz crystal. Writing to EXCLK should be done before asynchronous operation is selected.
Note that the crystal Oscillator will only run when this bit is zero.
Bit
(0xB2)
Read/Write
Initial Value
Bit
(0xB3)
Read/Write
Initial Value
Bit
(0xB6)
Read/Write
Initial Value
CS22
0
0
0
0
1
1
1
1
Clock Select Bit Description
R
R/W
R/W
7
–
0
7
0
7
0
CS21
0
0
1
1
0
0
1
1
R
6
–
0
R/W
R/W
6
0
6
0
CS20
R
5
–
0
R/W
R/W
0
1
0
1
0
1
0
1
5
0
5
0
EXCLK
R/W
4
0
R/W
R/W
Description
No clock source (Timer/Counter stopped).
clk
clk
clk
clk
clk
clk
clk
4
0
4
0
OCR2A[7:0]
TCNT2[7:0]
T2S
T2S
T2S
T2S
T2S
T
T
2
2
S
S
/256 (From prescaler)
/1024 (From prescaler)
/(No prescaling)
/8 (From prescaler)
/32 (From prescaler)
/64 (From prescaler)
/128 (From prescaler)
AS2
R/W
3
0
R/W
R/W
3
0
3
0
TCN2UB
ATmega329P/3290P
R
2
0
R/W
R/W
2
0
2
0
OCR2UB
R
1
0
R/W
R/W
1
0
1
0
TCR2UB
R/W
R/W
R
0
0
0
0
0
0
OCR2A
TCNT2
ASSR
157