ATmega329P Atmel Corporation, ATmega329P Datasheet - Page 16

no-image

ATmega329P

Manufacturer Part Number
ATmega329P
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega329P

Flash (kbytes)
32 Kbytes
Pin Count
64
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
54
Ext Interrupts
17
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
100
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega329P-20AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329P-20ANR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329P-20AU
Manufacturer:
INTEL
Quantity:
19
Part Number:
ATmega329P-20AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329P-20AU
Manufacturer:
ATMEL
Quantity:
8 000
Company:
Part Number:
ATmega329P-20AU
Quantity:
1 000
Part Number:
ATmega329P-20AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329PA-AU
Manufacturer:
NXP
Quantity:
12 000
Part Number:
ATmega329PA-AU
Manufacturer:
AT
Quantity:
20 000
Part Number:
ATmega329PA-MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega329PA-MUR
Manufacturer:
ATMEL
Quantity:
101
6.8
8021G–AVR–03/11
Reset and Interrupt Handling
Figure 6-5.
The Atmel
Reset Vector each have a separate program vector in the program memory space. All interrupts
are assigned individual enable bits which must be written logic one together with the Global
Interrupt Enable bit in the Status Register in order to enable the interrupt. Depending on the Pro-
gram Counter value, interrupts may be automatically disabled when Boot Lock bits BLB02 or
BLB12 are programmed. This feature improves software security. See the section
gramming” on page 296
The lowest addresses in the program memory space are by default defined as the Reset and
Interrupt Vectors. The complete list of vectors is shown in
determines the priority levels of the different interrupts. The lower the address the higher is the
priority level. RESET has the highest priority, and next is INT0 – the External Interrupt Request
0. The Interrupt Vectors can be moved to the start of the Boot Flash section by setting the IVSEL
bit in the MCU Control Register (MCUCR). Refer to
The Reset Vector can also be moved to the start of the Boot Flash section by programming the
BOOTRST Fuse, see
281.
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared and all interrupts are dis-
abled. The user software can write logic one to the I-bit to enable nested interrupts. All enabled
interrupts can then interrupt the current interrupt routine. The I-bit is automatically set when a
Return from Interrupt instruction – RETI – is executed.
There are basically two types of interrupts. The first type is triggered by an event that sets the
Interrupt Flag. For these interrupts, the Program Counter is vectored to the actual Interrupt Vec-
tor in order to execute the interrupt handling routine, and hardware clears the corresponding
Interrupt Flag. Interrupt Flags can also be cleared by writing a logic one to the flag bit position(s)
to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is
cleared, the Interrupt Flag will be set and remembered until the interrupt is enabled, or the flag is
cleared by software. Similarly, if one or more interrupt conditions occur while the Global Interrupt
Enable bit is cleared, the corresponding Interrupt Flag(s) will be set and remembered until the
Global Interrupt Enable bit is set, and will then be executed by order of priority.
The second type of interrupts will trigger as long as the interrupt condition is present. These
interrupts do not necessarily have Interrupt Flags. If the interrupt condition disappears before the
interrupt is enabled, the interrupt will not be triggered.
When the AVR exits from an interrupt, it will always return to the main program and execute one
more instruction before any pending interrupt is served.
Register Operands Fetch
ALU Operation Execute
Total Execution Time
®
Result Write Back
AVR
Single Cycle ALU Operation
®
provides several different interrupt sources. These interrupts and the separate
clk
”Boot Loader Support – Read-While-Write Self-Programming” on page
CPU
for details.
T1
”Interrupts” on page 53
T2
ATmega329P/3290P
”Interrupts” on page
T3
for more information.
53. The list also
”Memory Pro-
T4
16

Related parts for ATmega329P