ATmega329P Atmel Corporation, ATmega329P Datasheet - Page 300

• Manufacturer Part Number: ATmega329P
• Manufacturer: Atmel Corporation

Specifications of ATmega329P

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.6.1
8021G–AVR–03/11
Signal Names
In this section, some pins of the ATmega329P/3290P are referenced by signal names describ-
ing their functionality during parallel programming, see
described in the following table are referenced by pin names.
The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a positive pulse.
The bit coding is shown in
When pulsing WR or OE, the command loaded determines the action executed. The different
Commands are shown in
Figure 27-1. Parallel Programming
Table 27-9.
Programming Mode
Signal Name in
RDY/BSY
PAGEL
DATA
BS1
XA0
XA1
BS2
WR
OE
Pin Name Mapping
RDY/BSY
Table
Pin Name
Table
PAGEL
+12 V
PB7-0
BS2
BS1
XA0
XA1
PD1
PD2
PD3
PD4
PD5
PD6
PD7
WR
PA0
OE
27-12.
27-11.
I/O
I/O
O
PD1
PD2
PD3
PD4
PD5
PD6
PD7
RESET
XTAL1
GND
PA0
I
I
I
I
I
I
I
Function
0: Device is busy programming, 1: Device is ready for
new command.
Output Enable (Active low).
Write Pulse (Active low).
Byte Select 1 (“0” selects low byte, “1” selects high
byte).
XTAL Action Bit 0
XTAL Action Bit 1
Program Memory and EEPROM data Page Load.
Byte Select 2 (“0” selects low byte, “1” selects 2’nd high
byte).
Bi-directional Data bus (Output when OE is low).
PB7 - PB0
AVCC
VCC
Figure 27-1
ATmega329P/3290P
+5V
+5V
DATA
and
Table
27-9. Pins not
300