ATmega329P Atmel Corporation, ATmega329P Datasheet - Page 329

no-image

ATmega329P

Manufacturer Part Number
ATmega329P
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega329P

Flash (kbytes)
32 Kbytes
Pin Count
64
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
54
Ext Interrupts
17
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
100
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega329P-20AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329P-20ANR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329P-20AU
Manufacturer:
INTEL
Quantity:
19
Part Number:
ATmega329P-20AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329P-20AU
Manufacturer:
ATMEL
Quantity:
8 000
Company:
Part Number:
ATmega329P-20AU
Quantity:
1 000
Part Number:
ATmega329P-20AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega329PA-AU
Manufacturer:
NXP
Quantity:
12 000
Part Number:
ATmega329PA-AU
Manufacturer:
AT
Quantity:
20 000
Part Number:
ATmega329PA-MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega329PA-MUR
Manufacturer:
ATMEL
Quantity:
101
27.8.21
27.8.22
27.8.23
27.8.24
8021G–AVR–03/11
Programming the Lock Bits
Reading the Fuses and Lock Bits
Reading the Signature Bytes
Reading the Calibration Byte
8. Poll for Fuse write complete using programming instruction 6g, or wait for t
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Lock bit write using programming instruction 7a.
3. Load data using programming instructions 7b. A bit value of “0” will program the corre-
4. Write Lock bits using programming instruction 7c.
5. Poll for Lock bit write complete using programming instruction 7d, or wait for t
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Fuse/Lock bit read using programming instruction 8a.
3. To read all Fuses and Lock bits, use programming instruction 8e.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Signature byte read using programming instruction 9a.
3. Load address 0x00 using programming instruction 9b.
4. Read first signature byte using programming instruction 9c.
5. Repeat steps 3 and 4 with address 0x01 and address 0x02 to read the second and third
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Calibration byte read using programming instruction 10a.
3. Load address 0x00 using programming instruction 10b.
Read the calibration byte using programming instruction 10c.
Table 27-15 on page
sponding lock bit, a “1” will leave the lock bit unchanged.
to
To only read Fuse High byte, use programming instruction 8b.
To only read Fuse Low byte, use programming instruction 8c.
To only read Lock bits, use programming instruction 8d.
signature bytes, respectively.
Table 27-15 on page
309).
309).
ATmega329P/3290P
WLRH
WLRH
(refer to
(refer
329

Related parts for ATmega329P