ATmega48 Atmel Corporation, ATmega48 Datasheet - Page 12

• Manufacturer Part Number: ATmega48
• Manufacturer: Atmel Corporation

Specifications of ATmega48

• Flash (kbytes): 4 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 256
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Note:
12
0x1B (0x3B)
0x1A (0x3A)
0x0E (0x2E)
0x0D (0x2D)
0x0C (0x2C)
0x0B (0x2B)
0x0A (0x2A)
Address
0x19 (0x39)
0x18 (0x38)
0x17 (0x37)
0x16 (0x36)
0x15 (0x35)
0x14 (0x34)
0x13 (0x33)
0x12 (0x32)
0x11 (0x31)
0x10 (0x30)
0x0F (0x2F)
0x09 (0x29)
0x08 (0x28)
0x07 (0x27)
0x06 (0x26)
0x05 (0x25)
0x04 (0x24)
0x03 (0x23)
0x02 (0x22)
0x01 (0x21)
0x0 (0x20)
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these
3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI
4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O
5. Only valid for ATmega88/168
ATmega48/88/168
should never be written.
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The Atmel
ATmega48/88/168 is a complex microcontroller with more peripheral units than can be supported within the 64 location
reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only the
ST/STS/STD and LD/LDS/LDD instructions can be used.
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Name
PORTD
PORTC
PORTB
PCIFR
DDRD
TIFR2
TIFR1
TIFR0
DDRC
DDRB
PIND
PINC
PINB
PORTD7
PORTB7
Bit 7
PIND7
PINB7
DDD7
DDB7
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD6
PORTC6
PORTB6
Bit 6
PIND6
PINC6
PINB6
DDD6
DDC6
DDB6
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD5
PORTC5
PORTB5
PIND5
PINC5
Bit 5
DDD5
DDC5
PINB5
DDB5
ICF1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD4
PORTC4
PORTB4
PIND4
PINC4
Bit 4
DDD4
DDC4
PINB4
DDB4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD3
PORTC3
PORTB3
PINC3
Bit 3
PIND3
PINB3
DDD3
DDC3
DDB3
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD2
PORTC2
PORTB2
OCF2B
OCF1B
OCF0B
Bit 2
PCIF2
PIND2
PINC2
PINB2
DDD2
DDC2
DDB2
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD1
PORTC1
PORTB1
OCF2A
OCF1A
OCF0A
PIND1
PINC1
Bit 1
PCIF1
PINB1
DDD1
DDC1
DDB1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD0
PORTC0
PORTB0
Bit 0
PCIF0
PIND0
PINC0
PINB0
DDD0
DDC0
DDB0
TOV2
TOV1
TOV0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
2545TS–AVR–05/11
Page
157
135
87
87
87
86
86
86
86
86
86