ATmega48 Automotive Atmel Corporation, ATmega48 Automotive Datasheet - Page 117

• Manufacturer Part Number: ATmega48 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega48 Automotive

• Flash (kbytes): 4 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 256
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

14.11.4
14.11.5
14.11.6
7701E–AVR–02/11
TCNT1H and TCNT1L – Timer/Counter1
OCR1AH and OCR1AL – Output Compare Register 1 A
OCR1BH and OCR1BL – Output Compare Register 1 B
A FOC1A/FOC1B strobe will not generate any interrupt, nor will it clear the timer in clear timer
on compare match (CTC) mode using OCR1A as top. The FOC1A/FOC1B bits are always
read as zero.
• Bit 5..0 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must
be written to logical zero when the register is written.
The two timer/counter I/O locations (TCNT1H and TCNT1L, combined TCNT1) give direct
access for both read and for write operations to the timer/counter unit's 16-bit counter. To
ensure that both the high and low bytes are read and written simultaneously when the CPU
accesses these registers, the access is performed using an 8-bit temporary high byte register
(TEMP). This temporary register is shared by all the other 16-bit registers. See
16-bit Registers” on page
Modifying the counter (TCNT1) while the counter is running introduces a risk of missing a
compare match between TCNT1 and one of the OCR1x registers.
Writing to the TCNT1 register blocks (removes) the compare match on the following timer
clock for all compare units.
The Output Compare Registers contain a 16-bit value that is continuously compared with the
counter value (TCNT1). A match can be used to generate an Output Compare interrupt, or to
generate a waveform output on the OC1x pin.
The output compare registers are 16 bits in size. To ensure that both the high and low bytes
are written simultaneously when the CPU writes to these registers, the access is performed
using an 8-bit temporary high byte register (TEMP). This temporary register is shared by all
the other 16-bit registers. See
Bit
0x2D (0x4D)
0x2C (0x4C)
Read/Write
Initial Value
Bit
0x2B (0x4B)
0x2A (0x4A)
Read/Write
Initial Value
Bit
0x29 (0x49)
0x28 (0x48)
Read/Write
Initial Value
R/W
R/W
R/W
7
0
7
0
7
0
R/W
R/W
R/W
6
0
6
0
6
0
94.
Atmel ATtiny24/44/84 [Preliminary]
“Accessing 16-bit Registers” on page
R/W
R/W
R/W
5
0
5
0
5
0
R/W
R/W
R/W
4
0
4
OCR1A[15:8]
0
4
OCR1B[15:8]
0
TCNT1[15:8]
OCR1A[7:0]
OCR1B[7:0]
TCNT1[7:0]
R/W
R/W
R/W
3
0
3
0
3
0
R/W
R/W
R/W
2
0
2
0
2
0
94.
R/W
R/W
R/W
1
0
1
0
1
0
R/W
R/W
R/W
0
0
0
0
0
0
“Accessing
OCR1AH
OCR1AL
OCR1BH
OCR1BL
TCNT1H
TCNT1L
117