ATmega48PA Atmel Corporation, ATmega48PA Datasheet - Page 298

• Manufacturer Part Number: ATmega48PA
• Manufacturer: Atmel Corporation

Specifications of ATmega48PA

• Flash (kbytes): 4 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 256
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

28.2
8271D–AVR–05/11
Fuse Bits
Table 28-3.
Notes:
The ATmega48A/PA/88A/PA/168A/PA/328/P has three Fuse bytes.
describe briefly the functionality of all the fuses and how they are mapped into the Fuse bytes.
Note that the fuses are read as logical zero, “0”, if they are programmed.
Table 28-4.
Extended Fuse Byte
–
–
–
–
–
–
–
SELFPRGEN
BLB0 Mode
BLB1 Mode
1
2
3
4
1
2
3
4
1. Program the Fuse bits and Boot Lock bits before programming the LB1 and LB2.
2. “1” means unprogrammed, “0” means programmed
Lock Bit Protection Modes
Extended Fuse Byte for ATmega 48A/48PA
BLB02
BLB12
1
1
0
0
1
1
0
0
ATmega48A/PA/88A/PA/168A/PA/328/P
BLB01
BLB11
Bit No
1
0
0
1
1
0
0
1
7
6
5
4
3
2
1
0
No restrictions for SPM or LPM accessing the Application
section.
SPM is not allowed to write to the Application section.
SPM is not allowed to write to the Application section, and LPM
executing from the Boot Loader section is not allowed to read
from the Application section. If Interrupt Vectors are placed in
the Boot Loader section, interrupts are disabled while executing
from the Application section.
LPM executing from the Boot Loader section is not allowed to
read from the Application section. If Interrupt Vectors are placed
in the Boot Loader section, interrupts are disabled while
executing from the Application section.
No restrictions for SPM or LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and LPM
executing from the Application section is not allowed to read
from the Boot Loader section. If Interrupt Vectors are placed in
the Application section, interrupts are disabled while executing
from the Boot Loader section.
LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
Description
–
–
–
–
–
–
–
Self Programming Enable
(1)(2)
. Only ATmega88A/88PA/168A/168PA/328/328P.
Default Value
1
1
1
1
1
1
1
1 (unprogrammed)
Table 28-5
-
Table 28-9
298