ATmega8515 Atmel Corporation, ATmega8515 Datasheet - Page 103

no-image

ATmega8515

Manufacturer Part Number
ATmega8515
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega8515

Flash (kbytes)
8 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
35
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
3
Input Capture Channels
1
Pwm Channels
3
32khz Rtc
No
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA8515
Manufacturer:
ATMEL
Quantity:
5 510
Part Number:
ATMEGA8515
Manufacturer:
NS
Quantity:
5 510
Part Number:
ATMEGA8515
Manufacturer:
AT
Quantity:
20 000
Part Number:
ATmega8515-16AC
Manufacturer:
MOT
Quantity:
3 450
Part Number:
ATmega8515-16AC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AI
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AJ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL
Quantity:
4 500
Part Number:
ATmega8515-16AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16JU
Quantity:
1 831
Part Number:
ATmega8515-16PU
Manufacturer:
AT
Quantity:
20 000
Timer/Counter Clock
Sources
Counter Unit
2512K–AVR–01/10
The Timer/Counter can be clocked by an internal or an external clock source. The clock
source is selected by the Clock Select logic which is controlled by the Clock Select
(CS12:0) bits located in the Timer/Counter Control Register B (TCCR1B). For details on
clock sources and prescaler, see “Timer/Counter0 and Timer/Counter1 Prescalers” on
page 95.
The main part of the 16-bit Timer/Counter is the programmable 16-bit bi-directional
counter unit. Figure 48 shows a block diagram of the counter and its surroundings.
Figure 48. Counter Unit Block Diagram
Signal description (internal signals):
The 16-bit counter is mapped into two 8-bit I/O memory locations: Counter High
(TCNT1H) containing the upper eight bits of the counter, and Counter Low (TCNT1L)
containing the lower eight bits. The TCNT1H Register can only be indirectly accessed
by the CPU. When the CPU does an access to the TCNT1H I/O location, the CPU
accesses the high byte temporary register (TEMP). The temporary register is updated
with the TCNT1H value when the TCNT1L is read, and TCNT1H is updated with the
temporary register value when TCNT1L is written. This allows the CPU to read or write
the entire 16-bit counter value within one clock cycle via the 8-bit data bus. It is impor-
tant to notice that there are special cases of writing to the TCNT1 Register when the
counter is counting that will give unpredictable results. The special cases are described
in the sections where they are of importance.
Depending on the mode of operation used, the counter is cleared, incremented, or dec-
remented at each Timer Clock (clk
internal clock source, selected by the Clock Select bits (CS12:0). When no clock source
is selected (CS12:0 = 0) the timer is stopped. However, the TCNT1 value can be
accessed by the CPU, independent of whether clk
rides (has priority over) all counter clear or count operations.
The counting sequence is determined by the setting of the Waveform Generation mode
bits (WGM13:0) located in the Timer/Counter Control Registers A and B (TCCR1A and
TCCR1B). There are close connections between how the counter behaves (counts) and
Count
Direction
Clear
clk
TOP
BOTTOM
T
1
TCNTnH (8-bit)
TEMP (8-bit)
Increment or decrement TCNT1 by 1.
Select between increment and decrement.
Clear TCNT1 (set all bits to zero).
Timer/Counter clock.
Signalize that TCNT1 has reached maximum value.
Signalize that TCNT1 has reached minimum value (zero).
TCNTn (16-bit Counter)
DATA BUS
TCNTnL (8-bit)
(8-bit)
T
1
). The clk
T
1
can be generated from an external or
T
1
Count
Clear
is present or not. A CPU write over-
ATmega8515(L)
Control Logic
TOVn
(Int.Req.)
clk
Tn
103

Related parts for ATmega8515