ATmega8515 Atmel Corporation, ATmega8515 Datasheet - Page 180

• Manufacturer Part Number: ATmega8515
• Manufacturer: Atmel Corporation

Specifications of ATmega8515

• Flash (kbytes): 8 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 35
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 3
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Fuse bits
180
ATmega8515(L)
Table 82. Lock Bit Protection Modes
Notes:
The ATmega8515 has two Fuse bytes. Table 83 and Table 84 describe briefly the func-
tionality of all the fuses and how they are mapped into the fuse bytes. Note that the
Fuses are read as logical zero, “0”, if they are programmed.
Table 83. Fuse High Byte
Notes:
Fuse High Byte
S8515C
WDTON
SPIEN
CKOPT
EESAVE
BOOTSZ1
BOOTSZ0
BOOTRST
1
2
3
4
(1)(2)
Memory Lock bits
1. Program the Fuse bits before programming the Lock bits.
2. “1” means unprogrammed, “0” means programmed
1. See “AT90S4414/8515 Compatibility Mode” on page 4 for details.
2. The SPIEN Fuse is not accessible in serial programming mode.
3. The CKOPT Fuse functionality depends on the setting of the CKSEL bits. See “Clock
4. The default value of BOOTSZ1..0 results in maximum Boot Size. See Table 78 on
(3)
Sources” on page 35. for details.
page 177.
1
1
0
0
Bit no
7
6
5
4
3
2
1
0
1
0
0
1
Description
AT90S4414/8515 compatibility
mode
Watchdog Timer always on
Enable Serial Program and Data
Downloading
Oscillator options
EEPROM memory is preserved
through the Chip Erase
Select Boot Size (see Table 78 for
details)
Select Boot Size (see Table 78 for
details)
Select Reset Vector
Protection Type
No restrictions for SPM or LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section,
and LPM executing from the Application section is not
allowed to read from the Boot Loader section. If Interrupt
Vectors are placed in the Application section, interrupts
are disabled while executing from the Boot Loader section.
LPM executing from the Application section is not allowed
to read from the Boot Loader section. If Interrupt Vectors
are placed in the Application section, interrupts are
disabled while executing from the Boot Loader section.
(2)
(Continued)
1 (unprogrammed)
1 (unprogrammed)
Default Value
1 (unprogrammed)
0 (programmed, SPI prog.
enabled)
1 (unprogrammed)
1 (unprogrammed,
EEPROM not preserved)
0 (programmed)
0 (programmed)
2512K–AVR–01/10
(4)
(4)